Bedienungsanleitung Gossen Metrawatt METRISO 5024 (Seite 5 von 14) (Englisch)

590652

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

GMC-I Messtechnik GmbH 5

uppermost scale, low-resistance at the middle scale and voltage at

the bottom scale. The device’s operating status and battery charge

level are indicated with the 2-color LED in the scale (Figure 1).

The battery compartment is located in the housing base (6). The

procedure for replacing batteries is described in 3.2.

All measurements are performed with two test probes:

• One test probe (1) is permanently attached to the housing –

positive pole.

• The other (8) is attached to a coil cord – negative pole

This test probe (8) can be inserted into the opening (9) and secured

by snapping the handle into the detaining fork (7).

As long as the toggle switch (4) is in the neutral middle position, the

METRISO 5024 can be utilized as a voltmeter.

The rotary switch must be set either to the 100 V, 250 V or 500 V

position in order to perform voltage measurements. No batteries are

required for this function.

The rotary switch must be set to the Ω position in order to perform

low-resistance measurements. Measurement is performed with the

toggle switch (4) in the Ω position. Voltage cannot be measured as

long as the rotary switch (3) remains in this position.

The desired test voltage must be selected with the rotary switch (3)

before performing insulation measurements. Measurement is

performed with the toggle switch (4) in the MΩ position.

3 Preparation for Device Operation

3.1 Unpacking the Device

Check for mechanical damage after unpacking the device. The

device is ready for use as soon as the batteries have been inserted

into the battery compartment.

3.2 Power Supply – Battery Replacement

The METRISO 5024 is operated exclusively with batteries for safety

reasons. Batteries are inserted or replaced as follows:

Ð First disconnect the measurement cables from the device under

test.

Ð Loosen the fastening screw at the bottom of the battery

compartment (6) and remove the battery compartment.

Ð Remove the depleted batteries and replace them with new or

fully charged batteries. Make sure that battery polarity is not

reversed during insertion (see printed symbols on the

compartment).

Ð Push the battery compartment back in and secure it with the

screw.

Recommended batteries: 4 ea. alkaline batteries per LR6, mignon

cells, AA cells, 1.5 V, at least 2300 mAh

3.3 Checking the Mechanical Zero Point

Ð Lay the device horizontally onto a work surface.

Ð Check the pointer for correct zero point adjustment and reset

with the adjusting screw (2a) if necessary.

The device may not be connected to a measuring circuit during

this procedure, and the toggle switch may not be activated.

Don’t forget: Negative pointer deflection is suppressed by the

scale’s limit stop. Always turn the adjusting screw clockwise for

this reason, and then slowly turn it counterclockwise until the 0 Ω

or 0 V position is reached.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gossen Metrawatt METRISO 5024 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info