Bedienungsanleitung Grandstream GXP-1100 (Seite 34 von 35) (Englisch)

470674

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

Grandstream Networks, Inc. GXP1100/1105 User Manual Page 33 of 34

Firmware version: 1.0.1.110 Last Updated: 01/2012

Instructions for Local TFTP Upgrade

1. Unzip the file and put all of them under the root directory of the TFTP server.

2. The PC running the TFTP server and the GXP1100/1105 should be in the same LAN

segment.

3. Go to File -> Configure -> Security to change the TFTP server's default setting from

"Receive Only" to "Transmit Only" for the firmware upgrade.

4. Start the TFTP server.

5. Configure the Firmware Server Path with the IP address of the PC

6. Update the change and reboot the unit

User can also choose to download the free HTTP server from http://httpd.apache.org/

or use Microsoft IIS

web server.

NOTE:

When GXP1100/1105 phone boots up, it will send TFTP or HTTP request to download configuration file

“cfg000b82xxxxxx”, where “000b82xxxxxx” is the MAC address of the GXP1100/1105 phone. This file is for

provisioning purpose. For normal TFTP or HTTP firmware upgrades, the following error messages in a TFTP

or HTTP server log can be ignored: “TFTP Error from [IP ADRESS] requesting cfg000b82023dd4: File does

not exist. Configuration File Download”

CONFIGURATION FILE DOWNLOAD

The GXP1100/1105 can be configured via Web Interface as well as via Configuration File (binary or XML)

through TFTP or HTTP/HTTPS. The “Config Server Path” is the TFTP or HTTP server path for the

configuration file. It needs to be set to a valid URL, either in FQDN or IP address format. The “Config Server

Path” can be the same or different from the “Firmware Server Path”.

A configuration parameter is associated with each particular field in the web configuration page. A parameter

consists of a Capital letter P and 2 to 4 digit numeric numbers. i.e., P2 is associated with “Admin Password”

in the ADVANCED SETTINGS page.

For a detailed parameter list, please refer to the link below to download the corresponding configuration

template of the firmware.

http://www.grandstream.com/support/tools

Once the GXP1100/1105 boots up (or re-booted), it will request a configuration file named “cfgxxxxxxxxxxxx”

followed by a request for configuration XML file named “cfgxxxxxxxxxxxx.xml”, where “xxxxxxxxxxxx” is the

MAC address of the device, i.e., “cfg000b820102ab”. The configuration file name should be in lower cases.

For more details on XML provisioning, please refer to http://www.grandstream.com/support

Managing Firmware and Configuration File Download

When “Automatic Upgrade” is set to “Yes”, a Service Provider can use P193 (Auto Check Interval, in

minutes, default and minimum is 60 minutes) to have the devices periodically check for upgrades at pre-

scheduled time intervals. By defining different intervals in P193 for different devices, a Server Provider can

manage and reduce the Firmware or Provisioning Server load at any given time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grandstream GXP-1100 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info