Bedienungsanleitung Grandstream GXP-2000 (Seite 43 von 44) (Englisch)

470665

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Grandstream Networks, Inc. GXP User Manual Page 43 of 44

Firmware 1.2.5.3 Last Updated: 03/2011

Instructions for local TFTP Upgrade:

1. Unzip the file and put all of them under the root directory of the TFTP server.

2. The PC running the TFTP server and the GXP should be in the same LAN segment.

3. Go to File -> Configure -> Security to change the TFTP server's default setting from

"Receive Only" to "Transmit Only" for the firmware upgrade.

4. Start the TFTP server, in the phone’s web configuration page

5. Configure the Firmware Server Path with the IP address of the PC

6. Update the change and reboot the unit

User can also choose to download the free HTTP server from

http://httpd.apache.org/ or use Microsoft IIS

web server.

NOTE:

• When GXP phone boots up, it will send TFTP or HTTP request to download configuration file

“cfg000b82xxxxxx”, where “000b82xxxxxx” is the MAC address of the GXP phone. This file is for

provisioning purpose. For normal TFTP or HTTP firmware upgrades, the following error messages in

a TFTP or HTTP server log can be ignored: “TFTP Error from [IP ADRESS] requesting

cfg000b82023dd4 : File does not exist. Configuration File Download”

CONFIGURATION FILE DOWNLOAD

The GXP can be configured via Web Interface as well as via Configuration File through TFTP or HTTP.

“Config Server Path” is the TFTP or HTTP server path for the configuration file. It needs to be set to a valid

URL, either in FQDN or IP address format.

A configuration parameter is associated with each particular field in the web configuration page. A

parameter consists of a Capital letter P and 2 to 4 digit numeric numbers. i.e., P2 is associated with “Admin

Password” in the ADVANCED SETTINGS page. For a detailed parameter list, please refer to the

corresponding configuration template of the firmware.

Once the GXP boots up (or re-booted), it will request a configuration file named “cfgxxxxxxxxxxxx”, where

“xxxxxxxxxxxx” is the MAC address of the device, i.e., “cfg000b820102ab”. The configuration file name

should be in lower cases.

NOTE : Since firmware 1.2.4.3, GXP280/GXP285/GXP1200 can be provisioned using XML configuration file.

Please refer to our XML provisioning guide using this link

http://www.grandstream.com/support/gxp_series/general/documents/GS-XML_Provisioning_Guide.pdf

Managing Firmware and Configuration File Download

When “Automatic Upgrade” is set to “Yes”, a Service Provider can use P193 (Auto Check Interval, in

minutes, default and minimum is 60 minutes) to have the devices periodically check for upgrades at pre-

scheduled time intervals. By defining different intervals in P193 for different devices, a Server Provider can

manage and reduce the Firmware or Provisioning Server load at any given time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grandstream GXP-2000 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Grandstream GXP-2000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info