637246
115
Zoom out
Zoom in
Vorherige Seite
1/117
Nächste Seite
Page 51/53
14. ERROR MESSAGE SCREEN
The error will be displayed on the LCDisplay.
[ INPUT VOLTAGE ]
[ NO BATTERY ]
[ REVERSE POLARITY ]
* The present input * A battery is not * A battery is
voltage is _0.00V. connected to the connected to the
* Please check the outpu t output in reverse !
input voltage. * Please connect the * Please correctly
* The input voltage battery to the connect the battery
must be 11-15V. to the output.
output then
restart !
[ OPEN CIRCUIT ]
[ SHORT-CIRCUITED ]
[LOW OUTPUT VOLTAGE ]
* A battery is * Output short- * Output voltage is
disconnected during circuited. lower than the
an operation. * Please check the selected cells or
output.
* Please reconnect voltages
the battery and * Please select
restart!
proper cells or
voltages
[HIGH OUTPUT VOLTAGE]
[TEMPERATURE SENSOR ]
[ BAT. TEMP TOO LOW ]
* Output voltage is * A temperature * Battery temp is too
higher than the sensor is connected low to be operated!
selected cells or in reverse or is
defective.
voltages
* Please select
proper cells or OUTPUT _0.000V
voltages BATT TEMP __0.0°F
[ BAT. TEMP TOO HIGH]
[ INTERNAL TEMP ]
[DATA COMMUNICATION ]
* Battery temp is too * Internal temp is * Something is wrong
high to be operated! too hot ! with the internal
* Contact Hobby circuit.
Services if this * Contact Hobby
message appears Services
often.
OUTPUT _0.000V
BATT TEMP __0.0°F
[ BAL.VOLTAGE HIGH ]
[ BAL.VOLTAGE LOW ]
[ CALIRATION DATA ]
* Balancer cells * Balancer cells *Either calibration
voltage is too voltage is too data or internal
high !! low !! circuit might have
over cell is [0] low cell is [0] been damaged.
[ NO SENSOR ]
[MOTOR OVER CURRENT ] [ LINK COMMAND ]
* Link order failed ! * A temp-sensor is * Please reconnect
Error occured in the not connected to the the motor and
counterpart channel ! restart!
port
* Please connect the
temp-sensor to the
port then restart !
[ CONNECTION ]
[ MOTOR FUNCTION ]
* selected cells and * Can not start the
cells connected to motor function,
the balancing port because other Output
are different ! is used !
* Please recheck and * Please stop other
restart !
Output function to
start the motor !
115

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Graupner PRX-5A - 6444 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info