Bedienungsanleitung Graupner U-16 - 2018 (Seite 3 von 6) (Englisch)

637248

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

No liability for printing errors. We reserve the right to introduce modifications. 04/2010

boat is running, as leaves and other debris may get caught in the power system components. The

motors and speed controller could then be ruined by overloading.

• Dry cells and rechargeable batteries must never be short-circuited. Do not allow them to come into direct

contact with water.

• The battery charger features a time-controlled cut-off circuit. The battery should not be left on charge

unsupervised. The charge process must not be repeated in quick succession, as this would seriously

overcharge the battery, and possibly damage or even ruin it.

• Remove the batteries from the transmitter and charger if the model is not to be used for a long period.

• If the rechargeable battery in the model fails, do not dispose of it in the household rubbish. The pack

should be taken to your local battery disposal site. The model must be opened to remove the battery.

• Do not dispose of the electronic components in the model and the transmitter in the household rubbish.

Take them to your local specialist recycling centre; your local authority will tell you where it is located.

• Do not subject the model submarine, the charger or the transmitter to high levels of heat, cold or dirt.

• Secure the model, the charger and the transmitter carefully when transporting them. They may be

seriously damaged if they are free to slide about.

• Never operate the boat in moving water (e.g. a river), as its low speed and poor visibility in murky water

may result in the model drifting off downstream.

• If you have to salvage the model, take care not to risk your own life or that of others.

• Take particular care to ensure that the boat is completely watertight, as submarines will sink if too much

water enters the hull. Check the boat for damage before every run, and ensure that water cannot

penetrate. The switch flap must always be closed fully, i.e. flush with the hull, providing a watertight

seal.

• Allow the boat to dry out thoroughly after use.

Care and maintenance

• Clean the model carefully after every run, rinse the prepared model with clean water, and remove any

water which penetrates the hull. If water gets into the RC components, dry them out carefully and send

them to your nearest GRAUPNER Service Centre for checking.

• Clean the model and transmitter using suitable cleaning agents only. All you need is a lint-free cloth.

Never use chemical cleaners, solvents, methylated spirits, white spirit or similar.

• Lubricate the propeller shafts with a small drop of oil after each session, as the shaft bearings are also

the shaft seals. Use only a non-contaminating oil such as Order No. 206.

Operating instructions

• The first step is to fit the dry battery in the transmitter: undo the cross-point screw at the bottom of the

transmitter, and remove the cover plate. Insert the 9 V block battery with correct polarity, re-fit the cover

plate and tighten the retaining screw again.

Screw in

Unscrew

9 V block

battery

type 6F22

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner U-16 - 2018 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner U-16 - 2018

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info