Bedienungsanleitung Grohe 29067 BauMetric (Seite 5 von 8) (Deutsch, Englisch)

759550

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Application

Can be used in conjunction with:

• Pressurised storage heaters

• Thermally controlled instantaneous heaters

• Hydraulically controlled instantaneous heaters

Operation with unpressurised storage heaters (= open water

heaters) is not possible.

Technical data

• Flow pressure

- min. 0.5 bar

- recommended 1 - 5 bar

• Operating pressure max. 10 bar

• Test pressure 16 bar

A pressure reducing valve must be fitted in the supply line if

static pressures exceed 5 bar to satisfy noise level ratings.

Avoid major pressure differences between hot and cold water

supply.

• Flow rate at 3 bar flow pressure: approx. 27 l/min

• Temperature

Hot water inlet: max. 80 °C

Recommended (energy saving): 60 °C

Scalding protection possible by fitting a temperature limiter

(see Replacement parts, fold-out page II, Prod. no.: 46 375).

• Water connection hot - left

cold - right

Note (29 067):

This fitting can be combined with head and hand shower sets

by using a 3-way diverter.

Important note:

Never install shut-off valves in the outlet pipe (mixed

water) downstream of any built-in mixer.

Installation

Prepare the wall for the installation.

• Prepare the holes for the single lever mixer and slots for the

pipes.

Align single lever mixer using fitting template and fit,

see fold-out page I, Figs. [1] and [2].

• Permissible tolerances are given on the dimensional

drawing.

• The arrow on the fitting template must point upwards.

• To align place a spirit level on the cam on the fitting

template (A), see Fig. [1].

• The finished surface of the wall (B) must lie within the

area (X) of the fitting template, see Fig. [2].

• The cold water supply must be connected on the right, hot

water supply on the left.

Connect pipes.

Open cold and hot-water supply and check connections

for water-tightness.

Flush piping system prior and after installation of fitting

thoroughly (Consider EN 806)!

Plaster and tile the wall.

Do not remove the fitting template before final installation.

Final installation

Remove fitting template.

Note:

First fit the diverter (D) if installing trim set 29 061, see fold-out

page I, Fig. [3].

1. Remove screw plug (E).

2. Screw diverter (D) into position using 17mm socket spanner

and tighten.

Flow rate limiter

This mixer is fitted with a flow rate limiter, permitting an

infinitely variable individual reduction in flow rate. The highest

possible flow rate is set at the factory before despatch.

The use of flow rate limiters in combination with hydraulic

instantaneous heaters is not recommended.

To activate, see Fig. [4].

Install escutcheon and lever, see Figs. [5] and [6].

If the escutcheon can not be pushed far enough onto the cap,

an extension (see replacement parts, fold-out page II,

Prod. no.: 46 807 = 25mm / 46 808 = 50mm) must also be

installed.

Additionally seal the top edge of the escutcheon with silicone

when fitting against a particularly rough surface (deep tile

joints, highly textured tile).

Check mixer for correct operation, see fold-out page III,

Fig. [7].

Function of automatic diverter (D), see Fig. [8].

Pulling the lever will release water delivery.

On the bath mixer, water will always emerge from the lower

outlet first (e.g. bath outlet).

Pressing diverter (D) shuts off the flow of water to the bath and

delivers water to the shower outlet.

When the mixer is closed, the diverter is released

automatically so that when the mixer is opened again, water

will always emerge from the lower outlet first (e.g. bath outlet).

Maintenance

Inspect and clean all parts, replace as necessary and lubricate

with special grease.

Shut off hot and cold water supply.

I. Replacing the cartridge (F), see fold-out page III, Figs. [9]

to [11].

Observe the correct installation position!

Ensure that the cartridge seals engage in the grooves of the

housing. Fit screws (G) and tighten evenly and alternately.

II. Diverter (D), see fold-out page III, Figs. [9] to [11].

Replacement parts, see fold-out page II (* = special

accessories).

Care

For directions on the care of this fitting, refer to the

accompanying Care Instructions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grohe 29067 BauMetric Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info