Bedienungsanleitung Grohe Minta (Seite 4 von 8) (Englisch, Französisch, Spanisch)

626519

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

English

Application

Operation is possible in conjunction with:

• Pressurized storage heaters

Operation is not possible with:

• Low-pressure storage heaters (displacement water heaters)

Specification

• Max. flow

8.3 L/min or 2.2 gpm/60 psi

GROHE WaterCare 5.7 L/min or 1.5 gpm/60 psi

• Flow pressure

- min. 7.25 psi

- recommended 14.5 - 72.5 psi

- greater than 72.5 psi, fit pressure reducing valve

• Max. operating pressure 145 psi

• Test pressure 232 psi

• Temperature

- max. (hot water inlet) 176 °F

• Water connection: cold - RH hot - LH

• Deck thickness max. 2 3/8"

• Non reversible cartridge

Notes:

- Major pressure differences between cold and hot water supply

should be avoided.

- To be installed according to local codes and regulations.

- This faucet is not intended for the use with portable appliances.

Installation

Flush piping system prior and after installation of faucet

thoroughly!

Prepare sink faucet

Refer to the dimensional drawing on fold-out page I.

Mount sink faucet, see fold-out page II, fig. [1].

1. Fit O-Ring (A).

2. Insert faucet into sink. Feed the connection hoses separately

through the sink.

3. Fit brace (B), if necessary, with washer (C) and connect nut (D)

with tube (E). To do this, insert fitting key (G) into tube (E) and

turn fitting key (G) clockwise to fasten faucet.

(Tube may also have to be turned with an 22mm open ended

wrench.)

Note:

If brace (B) is omitted, deck thickness can be increased by 9/16"

to a total of 2 3/8".

The following lever positions can also be obtained, see fig. [2].

Connect sink faucet, see figs. [1] and [3].

- Cold water connection (marked blue) = right

- Hot water connection (marked red) = left

Avoid cross connection. The cartridge is not reversible.

Connect spray hose (H) and rinse spray (K), see figs. [4] to [7].

1. Feed the spray hose (H) through the spout (J), see fig. [4].

2. Feed the spray hose (H) through the faucet body from above and

fit spout (J) so that it snaps into place, see fig. [5].

3. Connect the rinse spray (K) without using any additional seals to

the spray hose (H), see fig. [6].

4. With rinse spray inserted slide on spring (L) onto spray hose (H)

from below.

5. Install the snap coupling (M) on the end of the spray hose (H)

and tighten by hand.

6. Pull the sleeve (M1) of the snap coupling (M) downwards and fit

to the union (N).

To ensure that the rinse spray (K) is correctly seated when

inserted, lug (J1) on the spout must engage in recess on the rinse

spray (K1), see fig. [7].

Open cold and hot water supply and check connections for

leakage!

Operation

1. Lever head (Lever head position right)

Slide lever to right = open (water flow)

Slide lever to left = closed

Slide lever towards front = cold water

Slide lever towards back = hot water

2. Rinse spray

Open faucet. Water will always emerge first from the flow

straightener.

Diverter button:

Switching to spray flow by pushing the diverter button.

Turning off the faucet automatically diverts the water flow from

spray to flow straightener.

Flow rate limiter

This faucet is fitted with a flow rate limiter, permitting an infinitely

variable individual reduction of the flow rate. The highest possible

flow rate is set by the plant before despatch.

The use of flow rate limiters in combination with hydraulic

instantaneous water heaters is not recommended.

To activate see "Replacing the cartridge" point 1 to 4, figs. [9]

and [10].

Maintenance

Inspect and clean all parts, replace as necessary and grease with

special grease.

Shut off cold and hot water supply!

I. Replacing the cartridge, see fig. [9].

1. Lever out plug (O).

2. Loosen set screw (P) using a 3mm allen wrench.

3. Pull off lever (R).

4. Unscrew cap (S).

5. Remove screws (T) and detach complete cartridge (U).

6. Change the complete cartridge (U).

Assemble in reverse order.

Observe the correct installation position!

Make sure that the cartridge seals engage in the grooves on the

housing. Fit screws (T) and tighten evenly and alternately.

II. Flow straightener and spray, see fig. [11].

1. Unscrew rinse spray (K) and remove non-return valve (V).

2. Unscrew flow straightener (W) with fitting key (G).

Assemble in reverse order.

Replacement parts, see fold-out page I ( * = special accessories).

Care

Instructions for care of this faucet will be found in the Limited

Warranty supplement.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grohe Minta Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info