544972
51
Zoom out
Zoom in
Vorherige Seite
1/58
Nächste Seite
51
ENGLISH
Searching for digital terrestrial
TV channels manually
1 Open the menu with »M«.
2 Select the line
»SOURCE SETUP« with »
C
«
or
»
D
« and press »OK« to confirm.
The
»SOURCE SETUP« menu appears.
3 Select the line
»Source« with »
C
« or »
D
«
and press
»OK« to confirm.
Select the option
»Air« with »
B
«, »
A
«, »
C
«
or
»
D
« and press »OK« to confirm.
Caution:
7
The antenna power supply (line »Active
Antenna Power
«) may only be switched on
if the antenna is an active indoor antenna
with a signal amplifier and it is not already
supplied with a voltage via a mains plug
(or similar supply). Otherwise you may
cause a short circuit and irreparably dam-
age your antenna.
4 Select the
»Active Antenna Power«« with
»
C
« or »
D
«. Switch on the antenna power
supply for the antenna with
»
B
« or »
A
«
(
»On«).
5 Select
» Digital Manual Tuning« with »
C
« or
»
D
« and press »OK« to confirm.
The menu appears.
6
Enter the channel number directly with
»1 ... 0« and press »OK« to confirm.
After the search is complete, the channels
found are displayed in the
»Results« menu.
7 Press
»M« to finish the setting.
Note:
7
If you wish to remedy other television
channels, repeat steps 4 to 8.
8 Press
»M« to end the setting.
Tuning analogue television
channels
This setting is only necessary if you cannot re-
ceive any digital channels and you have not car-
ried out an analogue search during initial setup.
The television channels can be set directly or
using the scan.
Setting all analogue television
channels
Analogue channels are displayed in the channel
list after the digital channels.
Note:
7
Plug the rooftop antenna cable (for analogue
television channels) into the
»ANT IN«
socket on the television.
1 Open the menu with
»M«.
2 Select the line
»SOURCE SETUP« with »
C
«
or
»
D
« and press »OK« to confirm.
The
»SOURCE SETUP« menu appears.
3 Select the line
»Source« with »
C
« or »
D
«
and press
»OK« to confirm.
Select the option
»Air« or »Cable« with
»
B
«, »
A
«, »
C
« or »
D
« and press »OK«
to confirm.
4 Select the line
»Automatic Channel Search«
with
»
C
« or »
D
« and press »OK« to con-
firm.
Automativ Channel Search
Source
Automatic Service Update
CA - Modul
Active Antenna Power
Analogue Manual Tuning
Signal Information
Digital Manual Tuning
Program Table
Exit
Back
SOURECE SETUP
20.09.2010
15:46
Air
On
Not inserted
Off
OK
SPECIAL SETTINGS
----------------------------------------------------------------------------------------------------------
51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

grundig-22-vle-8220-wg

Suche zurücksetzen

  • Signalstärke steht auf 68 % und es kommt die Meldung kein Signal. Empfang über Satellit Eingereicht am 21-8-2017 21:47

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Grundig 22 VLE 8220 WG wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Grundig 22 VLE 8220 WG

Grundig 22 VLE 8220 WG Bedienungsanleitung - Deutsch - 58 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info