Bedienungsanleitung Gude 40205 (Seite 19 von 64) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

622199

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Troubleshooting

At all failures it is first necessary to check whether the

appliance is sufficiently and permanently supplied

with pneumatic oil.

Failure Cause Removal

Compressed air

leaking from the

cover hole

• O-rings are

damaged or

dirty, which has

been caused by

a foreign item.

• Clean or

replace the O-

rings.

Compressed air

leaking from the

valve

• O-rings are

damaged or the

valve is faulty.

• Replace the O-

rings and valve.

Compressed air

leaking between

the body and

cylinder cover

• Screws are

loosened. O-

rings are

damaged.

• Tighten the

screws.

Replace the O-

rings.

Piston not fully

returning, idle

strokes

• Appliance

placed too

weakly or too

shortly.

• Piston dragging

as it is not

lubricated.

• O-ring is faulty.

• Place the

appliance

stronger.

• Lubricate the

cylinder surface

contact.

• Replace the O-

ring, check the

operating

pressure.

Nails not fully

fired

• Air pressure too

low.

• Hose piping with

a too small

cross section.

• Appliance not

lubricated.

• Firing

mechanism

worn out.

• Gradually

increase the

pressure by 0.5

bar to make

sure nails are

fired properly.

• Hose piping

inner diameter

at least 6 mm.

• Clean and

lubricate the

parts.

• Grind the firing

mechanism

down by app.

0.2 mm.

Failure Cause Removal

Nails breaking

and overlapping

• Firing

mechanism

significantly

worn out.

• Appliance

placed too

weakly.

• Replace the

firing

mechanism.

• Place the

appliance

stronger.

Appliance

running too

slowly

• O-ring is

damaged.

• Valve is

damaged.

• Replace the O-

ring.

• Replace the

valve

completely.

Firing

mechanism is

blocked by nails

• Wrong nails

used.

• Firing

mechanism has

fray.

• Insert correctly

appropriate

nails.

• Remove the

firing

mechanism off

fray.

Appliance not

working

• Check the air

inlet. Operating

pressure may

be too low.

• Increase the

operating

pressure.

However, max.

operating

pressure must

be adhered to.

Irregular

appliance

operation

• Install a set of pins with a head

valve.

Air leaking from

the appliance in

the bottom part

• Tighten the screws or install the

absorber or a set of pins.

Wrong reverse

movement

• Clean the appliance and install an

absorber or a set of pins.

Other failures

• Contact an expert, seller or

distributor.

Clamps/nails

blocked in the

guide plate

• Magazine dirty

• Belt with

clamps/nails

not moving fully

forward

• Ram worn-out

• Clean (blow) the

magazine.

Wrong

clamps/nails

have been used.

Use appropriate

clamps/nails

Maintenance table

Following the maintenance instructions specified in

this document will provide this high-quality product

with long and trouble-free operation. Disconnect the

appliance from the compressed air source for

maintenance and treatment. To ensure long and

trouble-free working of your tacker/nailer, it is

necessary to clean it every day and regularly lubricate

it. For this purpose, special tool oil should only be

used:

Via oil mist

lubricator

A complete maintenance unit includes

an oil mist lubricator and is fitted on

the compressor.

Via lubricator on

the piping

In the immediate vicinity of the

appliance (app. 50 cm distance), a

lubricator sufficiently providing the

appliance with oil is installed on the

lubricator piping.

Manually If your appliance has no maintenance

unit or lubricator on piping, 3-5 oil

drops must be added to the

compressed air connection before the

pneumatic appliance is put into

operation. If the pneumatic appliance

has been out of service for several

days, 5-10 oil drops must be added to

the compressed air connection before

switching the appliance on. Store your

pneumatic appliances only in dry

rooms.

Lubricate the appliance with special oil for pneumatic

appliances using an extension if there has been a long

operation break.

Store the appliance in a cleaned, dry, dust-free condition

and at temperatures above 5° C.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude 40205 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info