Bedienungsanleitung Gude GRP 2500 (Seite 35 von 37) (Deutsch, Englisch)

625851

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

Mind to wear safety shoes to operate the plate vibrator – it is the only way of avoiding injuries and contusions

Prior to the commissioning

• manual and sure to follow safety instructions listed.

• Engine oil fill and oil level to ensure correct.

• Fuel (unleaded petrol) fill.

• Safety clothing

Installation and Commissioning (Fig. 1 / 2)

• Attach the handle (1) of the vibratory plates by screws on the guide bar (8).

Launch

• petrol tap (17)

• During cold engine WINDOW Choke, choke the engine in warm open (14)

• motor switch to "ON" (7)

• throttle slightly open (15)

• Starterseil draw - Note: If the oil level is too low the engine will not jump to.

• choke open while the engine warmläuft

• throttle fully open for operation

Parking

• Close throttle and idle speed to bring

• motor switch to "OFF" switch

• petrol cock closed

Step-by Step Instructions

1. Clear any foreign objects from the ground to be treated with the vibrator .

2. Always wear protection clothing .

3. Start the plate vibrator according to description in the manual. .

4. Observe all the relevant safety instructions and protection measures. .

5. Compact the ground to be treated slowly and evenly to obtain the best possible result.

Troubles-Causes-Troubleshooting

Trouble Cause Troubleshooting

Engine cannot be

started

1. Switch ON/OFF position .

2. No fuel

1. Refuel.

Engine runs unevenly

1. Engine gas lever still in the choke position .

2. Ignition plug loosened .

3. Dirty or dead fuel .

4. Jammed air filter .

5. Carburettor misadjusted .

6. Tank cover vent jammed .

1. Put the gas lever in position run.

2. Check the ignition plug .

3. Drain the dead fuel in a suitable container.

Pour fresh fuel in the tank .

4. Clean the air filter .

5. Have the carburettor adjusted .

6. Clean the tank cover and the vent .

Engine runs but the

machine will not be

vibrating

1. Not fully opened gas lever .

2. V-belt loosened or broken .

1. Open the lever at full .

2. Set up/replace V-belt (see inspections and

maintenance)

The plate slats or runs

unevenly

1. Loosened or damaged dampers .

2. Surface too hard .

1. Check the dampers, retighten or replace.

Inspections and Maintenance Safety Instructions

Turn the engine off before repairs, maintenance and leaving the vibrator .

Inspection and maintenance

V-belts

For new machines or installing a new belt, the belt tension after the first five hours of operation be reviewed. Then the belt every 50

hours of check and adjust.

Adjusting the strap

• The four screws on the strap loose and the protection belt protection decrease.

• The four screws that secure the engine to the console is attached, and the mother, with the rear part of the belt protection on the

console is attached, detach.

• The engine on the tightening of the belt to the rear (in the direction of handle), the loosening of the belt to the front slide.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gude GRP 2500 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info