Bedienungsanleitung Gys CT160 (Seite 5 von 23) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

625723

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

DESCRIPTION OF THE CHARGER (FIG I, PAGE 2)

The chargers CT 160 and CT 210 are designed to charge lead acid batteries with liquid electrolyte,

nominal voltage from 12V, and with capacity according to the table II, page 2.

1 – Ammeter 5 – Fuse

2 – Battery voltage selector 6 – cables + clamps

3 – Battery capacity selector 7 – handle (CT 210 only)

4 – Main switch 8 – Power supply (CT160 : fixed / CT210 : removable)

CHARGER MODE

Preliminary precautions

• For indoor use, with good ventilation. Protect the charger from rain and moisture.

• Remove the battery caps if there is, and check the level of liquid. If it is not correct, filled up with

distilled water. Clean well the battery terminals.

• Check if the battery capacity and voltage are compatible with your charger. Do not charge the

battery when it is connected on the vehicle

Connection and disconnection

• Connect the clamps (+ red, - black) to + and - battery terminals, making sure you get a good electric

contact, respecting the following order:

▪ Connect first the battery terminal not connected to the chassis of the vehicle.

▪ Then connect the other connection to the chassis remote from the battery and any fuel line.

▪ At last, plug in your charger to 230 V 50/60 Hz mains supply.

• Choose the charge voltage (12 / 24V) and the charge speed (normal or boost). The « Boost »

function allows charging a battery quickly.

Control and end of the charge process

• These are traditional chargers; the charge process must be stopped manually.

• The ammeter is a charge indicator. When the current drops down to 0, the battery charge is ending.

You can stop the charge process. In normal mode, it takes about 10 hrs to fully charge a battery. If

the ammeter is not at the minimum after this period, check the charge mode and voltage or have the

battery checked by a professional.

• Do not let the charger connected more than 24 Hours on a battery.

• After charging, disconnect the battery charger from main supply. Then remove the chassis connection

and the battery connection, in this order.

PROTECTIONS

Your product has been developed with a maximum of protections.

• The clamps of the battery are isolated.

• The polarity reversal will not cause danger. The protection is insured by an automotive fuse, which

must be changed in case of polarity error. Respect the rating of the fuse, which is indicated on the

charger.

• This device is protected by an internal fuse to avoid any risk in case of damage to the charger.

(CT160 : 1,6A – CT210 : 2A)

• Thermal protection: the transformer of the product is protected by a thermal switch. If the charger is

used intensively, it may switch in thermal protection mode (cooling time about 15min), and then

resume the charge.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gys CT160 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info