Bedienungsanleitung Gys TIG 250 AC-DC (Seite 5 von 24) (Englisch)

665714

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

This equipment must be used and stored in a place protected from dust, acid, gas or any other corrosive substance.

Attention: this equipment does not comply with the standard IEC61000-3-12. If the machine is connected to the

public network on low voltage, the installer and operator must ensure that the machine can be connected - consult

your power supplier if necessary.

In order to reduce possible electromagnetic disturbances, you can:

Install electric filters close to the socket in case of excessive conducted disturbances. The earth and torch cables

should be as short as possible and be placed close together as far as possible from any other cable, power tool or

electrical cables.

The electromagnetic fields can disturb other equipment, eg; pacemaker or hearing aid.

People wearing pacemakers are advised to consult their doctor before using this device.

Do not use the welding unit to thaw pipes.

Handle gas cylinders with care. There is increased danger if the bottle or it's valve are damaged.

Electric and magnetic fields may interfere with netwok cables and may cause disturbances.

Never wrap the welding leads around your body. Do not place your body between the earth and the torch cable,

they should be placed on the same side.

Electromagnetic disturbances should be reduced as much as possible if they disturb the operator's activity. The

operator is responsible for the installation and the use of the welding equipment and should seek advice from the

manufacturer if required.

Electric wiring rule to reduce disturbances

It is sometimes useful to set all the parts at the same voltage (while respecting the standards in place for each).

Installing an earth connection to the workpiece may reduce the disturbances, and will not increase the risk to the

operator or any other electrical appliances.

The shielding of the welding cables and of any other cables may be useful.

IP protection

IP23S

- Protection prevents access to hazardous parts with fingers or other solid foreign bodies with a diameter equal to or

higher than 12.5mm

- Protective grid - against rain fall at an angle of 60°.

- Case protects against effects of water/dust penetration when the equipment is not in use.

Set up

Only qualified personnel authorized by the manufacturer should perform the installation of the welding equipment.

During set up, the operator must ensure that the machine is unplugged. The serial or parallel connections on a

generator are prohibited.

Transportation of the machine

Two handles are fitted on the equipment to carry it easily, be careful to not underestimate its weight.

This machine is not equipped with a lifting fascility - the operator is required to make the necessary arrangements

for safe lifting and transport of the machine (be careful not to tilt the machine).

Do not use the cables or torch to move the machine. The welding equipment must be moved in an upright position.

Never lift the machine while there is a gas cylinder on the support shelf - follow the separate movement guidelines

specified for the gas bottle.

The removal of the wire reel from the machine is recommended before undertaking any lifting operation.

Setting up the machine

Rules to follow:

¤ Put the machine on the floor (maximum incline of 15°.)

¤ Ensure the work area has sufficient ventillation for welding, and that there is easy access to the control panel.

¤ The machine must be placed in a sheltered area away from rain or direct sunlight.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gys TIG 250 AC-DC Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info