Bedienungsanleitung Haas-Sohn I-CONTROL (Seite 6 von 11) (Englisch)

564801

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

between them). If the glass is dirty, we recommend increasing the firing intensity by

opening the primary air regulator, which usually supports the self-acting cleaning process.

5.5. Operation during temporary period and at worsened weather conditions

For temporary periods , for example, during the time when outdoor temperature is above

C, during rainy and wet days, in case of gusty wind, etc. the chimney effect may worsen

thus the smoke is not led away in full as usual. Therefore, during such period, you should

operate the fireplace stove with smallest possible quantity of fuel, to allow improving the

firing process and the chimney effect by opening the air inlets in case you need to make

adjustments.

5.6. How to substitute the blind element by the exchanger

Some models are provided with the so-called blind element that serves as the chimney

effect conditioner as well. After removal of such blind element, those models must be

completed with warm-water exchanger allowing connection to heating bodies to provide

heat in adjacent rooms or with a water back boiler. A warm water exchanger may be

supplied as special accessory (detailed instructions for operation and installation provided).

Order the installation of the fireplace stove with warm water exchanger at a specialist

company.

Caution! A fireplace stove equipped with a warm water exchanger must not be

operated without the connection to the warm water distribution system or the water

filled, or without anti-freezing mixture, respectively.

5.7. Ash removal

Depending on the length and the intensity of the firing process, you need to use a fire hook

or poking lever (if installed with the particular model) in order to knock the ash down the

grate to the ashpan. Monitor the content of the ashpan - do not allow too much ash in

it. Excessive ash may block the air supply under the grate thus causing problems at

fire setting or burning.

Always empty the ashpan when cold. The best approach is to empty the ashpan just before

you start preparing the next fire. Ash from wood may be used for composting or for

fertilizing.

Caution! Before you touch the ashpan to empty it, check it for fire brand. Prevent any

likely fire in the dustbin.

6. CLEANING AND MAINTENANCE

6.1. Cleaning

The fireplace stove (cold) needs cleaning at least once a year (after the season), or twice

or more (if needed). During the cleaning, you should remove any dirt caught in the smoke

flue, the firing area and on the partitions. Loose parts of the fireclay lining should be

repaired (i.e. replaced). Check the fireclay lining for integrity even during the heating

season. The gaps between the brick shapes are designed for heat dilatation, to avoid brick

cracking. Therefore YOU SHOULD NOT fill any sealing in the gaps (as it used be before

with older heating devices). Cracked fireclay bricks do not lose the function unless

they are completely fallen out of the position!

In the course of the cleaning procedure, we recommend you to remove all movable

partitions (for easier access in the area above them). To clean the glass, apply standard

cleaning agents designed for cleaning fireplace stove, cooker or oven. Use a soft cloth or

paper, or special agents designed for cleaning fireplace glass, e.g. CINEOL. Only clean the

glass when cold. For cleaning the painted surface, never use water: it is recommended to

clean such surface with sponge or soft flannel cloth.

Caution! With selected types of fireplace stove, the vertical side of the firing area is

provided with VERMICULITE. The same material is used for some chimney effect

conditioners. The material is irreparable. In case of any damage, just replace it.

Vermiculate products are characteristic with top heat-insulating parameters and good

resistance to cracking. The resistance to abrasion is somehow lower so it is recommended

to keep this in mind while reloading and cleaning.

6.2. Cleaning the ceramics and tiles

To clean ceramic tiles or tiles, it is recommended to use a dry or slightly wet cloth. Clean

the fireplace stove only while cold.

6.3. Sealing lines and tapes

Contact areas of doors and glass (or other parts of the heating device) are provided with a

special glass-ceramic sealing line (tape) that is resistant to high temperatures. We

recommend you to check the tape for integrity, and have it replaced if necessary.

After some time, any newly installed sealing tape lays flat so it is recommended to check

the tightness (the glass tightly installed in the door construction) after approx. 3 months of

usage. If you find any release, tighten the glass holders (carefully!)

6.4. Spare parts

In case of repair, use only original spare parts recommended by the manufacturer, see

Chapter 10.3 (Recommended spare parts). Identify the spare part with use of the Technical

Card (a part of the supply).

7. WHAT TO DO IF... ...Do you do it yourself?

Problem Cause Corrective action

Chimney or smoke flue sealing

(malfunction, “false” air is being

added).

Contact a chimney sweep (ask them to check the chimney).

For example, new sealing for the chimney door is needed.

Adjust the positions of smoke pipes or replace them if

damaged.

Chimney effect bad or not

working

Ask the chimney or fireplace stove specialist technician for

inspection to find out the reason and the solution (e.g.

cleaning the chimney, remove the smoke flue reduction

elements, higher chimney, more air in the room, etc.

The door of another heating

device connected to the same

chimney is open

Shut the door

Chimney cleaning holes are

open.

Close the cleaning holes

Smoke flue elements or

other parts of the heating

system are dirty or clogged

See 6.1.

Insufficient fresh air supply See 4.7.

Worsened weather conditions See 5.5.

Malfunction (weak fire, weak chimney effect) or excessive

smoke during reloading or during the firing

Wrong type of fuel was used for

burning

Provide proper kind of fuel, see 2.2.

Haas-Sohn I-CONTROL Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info