Bedienungsanleitung Haas-Sohn PALLAZZA-II 519.08 (Seite 5 von 33) (Englisch)

564778

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

Floor protection

The floor is to be protected from the radiant heat from

the area of the viewing window (combustion chamber).

In addition, for practical reasons associated with

cleaning it is recommended that you install your pellet

stove on a fireproof base that extends beyond the device

at the back and on the sides by at least 5 cm and at the

front by at least 50 cm. We have floor protection plates

(underlay plates or U plates) in our range of accessories.

If required, you may order them from your specialist

stove dealer. As an alternative, a tile or stone floor is of

course very suitable.

Safety gaps (minimum gaps):

During installation of the stove it is absolutely essential

to observe the official fire protection regulations. Ask

your district heating inspector about this.

The following must be maintained as the minimum

distances from flammable or temperature-sensitive

materials (e.g. furniture, wallpaper, wooden cladding)

and from loadbearing walls. (See drawing):

A 10 cm from the back wall

B 15 cm from the side walls and

C 80 cm in the direction of radiation.

Figure 2: Safety gaps

The chimney (fireplace or flue) must for example be

made of stainless steel or ceramics (glazed internally) so

that it cannot rot. This is necessary because of the low

temperature of flue gases from your pellet stove.

Standard trade flue tubes may be used for the

connection to the fireplace. Approved Flex steel flues

are also suitable.

Since excess pressure may build up at the smoke outlet

because of the way that the pellet stove works with an

induced draught fan, all fume outlet pipes as far as the

intake to the fireplace must be gas-tight. It is also

essential to ensure that the flue tube does not stick out

into the open cross-section of the chimney. The use of

wall lagging is recommended for the insertion into the

chimney. (See Figure 3).

With longer flue gas pipework, horizontal sections and

constrictions must be avoided and specially insulated

flue tubes should be used. Pipework rising in the

direction of the chimney is recommended.

Figure 3: Chimney connection

1 = Wall lagging

2 = Gas-tight pipework

3 = Underlay plate

External air intake:

In airtight buildings, whilst the pellet stove is operating, a

reduction in the oxygen level in the room where the

stove is installed may occur, so adequate ventilation

must be ensured. For this the pellet stove offers you the

option of operating independently of the air in the room.

To do this, connect the air intake elbow located on the

back (diameter: 57 mm) to a hose or a similar suitable

air duct. The end of the air duct must be located in the

open air or in a well-ventilated room within the building.

When installing the pellet stove in combination with

controlled residential room ventilation, the end of the air

intake duct must not be connected to the ventilation

system in an adjacent room with the air connection

system. To ensure sufficient volume of air intake, the

pipe should not be longer than about 3 m and not have

too many bends. This pipe should have a minimum

diameter of 5 cm. (The bigger, the better). If the pipe

goes to the open air, it must end with a downward 90°

bend or with wind protection. (See Figure 4).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Haas-Sohn PALLAZZA-II 519.08 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Haas-Sohn PALLAZZA-II 519.08

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info