Bedienungsanleitung Hadewe Hyperios3 (Seite 4 von 8) (Englisch)

659859

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Safety Instructions

To ensure that the burr/ tool sits firmly

in the chuck, do not work with tools

which:

• have an oily shaft

• are worn

• are bent.

Before using the equipment, assure

that:

• the tool can be pushed far enough

into the chuck

(Test this with a dipstick and clean

if necessary)

• the inserted tool will not cant

while clamping it

• the tool stuck properly in the chuck

• the tool is approved for using it at

the max. speed (see manufactur-

er’s instructions)

• the tool is absolutely dry.

For safety reasons do not change the

tool while the motor is running.

Empty the unit if it is not in use for a

longer period of time (e.g. before vaca-

tions). Clean out the tank. Set the

spray function on maximum. Now start

the spray function, and the water will

spray for approx. 3 min. The fluid will be

blown out of the complete spray system

and handpiece.

Always follow the operating instructions.

Do not carry out any repairs, modifica-

tions or maintenance work yourself.

This should only be done by a special-

ist. The mains cable may only be

changed by the producer. Never re-

move the housing, while the equipment

is plugged in as some components are

live. A spare parts list may be supplied

to qualified persons (repair workshops).

No responsibility can be accepted for

unauthorized or improper tampering

with the unit, which nullifies the guaran-

tee and any other liabilities.

Cleaning and disinfection

After every treatment please carry out

this steps:

Remove the rotating tool (e.g. bur) first.

To do so, pay attention to the instruc-

tions of its manufacturer.

Remove clothing remains through wip-

ing off easily the unit with a moistened

paper cloth. Afterwards clean all surfac-

es with a disinfection cloth (e.g.

Mikrozid AF cloths of Schülke and

Mayr).

Technical Details

Handpiece vibrates, is loud and/ or

becomes hot at the front part

Using bent tools  if so use a different

tool. (You can proof your tool with

our testing device 4990 if it is crook

or bent.)

Max. speed of the drill has been ex-

ceeded, which could cause a higher

vibration.  if so, consider instruc-

tions of the manufacturer of the bur.

Bur can not be insert easily

Use of bent / crook burs if so uses a

different tool. (You can proof your

tool with our testing device 4990 if it

is crook or bent.)

Chuck is full of dirt  cleaning the

chuck (see page 11)

Bur can not be clamped (does not

run)

Chuck is not tightened well

 Tighten the chuck according to in-

structions on page 7.

Knob of the handpiece is hard to use

Chuck is dirty/ soiled  clean the chuck

according to page 7.

Rubber ring under the knob twists while

using it.  Twist it of 180°

It does not spray

Pressure can not be set up in the tank,

because the lid is not tightened well.

There are parts of dirt in the spray sys-

tem  cleaning the spray system

according to page 10.

The blue water filter (art. No. 3479) in

the tank is blocked  Change the

water filter.

The unit does not work at all

Check the position of the main switch at

the back of the unit. It should be set on

“I“. (ON)

Foot switch is used all the time or it is

broken  Take off the socket of the

switch and try to start the machine

without the switch.

Pull the main switch to re- set the con-

trol unit.

After longer in use, it does not spray

Unit is overheated.  Slots of the unit

should not be covered or blocked.

Let cool down the unit for a while.

The noise level of the unit various

with its location

Depending on the background, where

the unit had been set up, the noise

level will vary.

The motor of the handpiece stutters

(e.g. 1 sec.) while switching it on

Very seldom this error might occur.

It would not damage the motor at all.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hadewe Hyperios3 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hadewe Hyperios3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info