Bedienungsanleitung Hadewe SPR3 (Seite 6 von 8) (Englisch)

659860

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Before using the unit

Please read through the instructions

carefully before using the unit and note

carefully the safety advises. Store the

manual safe and handy.

Scope of application

The equipment can be set up in a cabi-

net or can be used as a portable unit in

a carry case. It is suitable for the follow-

ing scopes:

• Footcare: Milling, trimming and polish-

ing. Attention: In fields of footcare

ones have to work with spray.

• Dental technique/ -laboratory:

Milling-, trimming and polishing work

at plaster casts and models (Do not

use this unit directly at the patient.)

•

Manicures: smoothing, trimming and

polishing.

Location of installing

The installation of the workroom must

correspond to the governing regula-

tions. Set up the appliance so that the

ventilation slits are not covered and the

exhaust air can escape well. Now con-

nect the power-supply plug to the elec-

tricity.

Fill in the spray liquid

Reduce the speed of the handpiece

with regulator (3) on minimum. Pull out

the spray tank at the grip. Hold on to the

tank cover with one hand and turn the

container of the tank off.

Now fill it with distilled water and anti

germ liquid (e.g. AQUA HY item no.

8555).

Do not exceed the maximum level

when filling the tank.

While screwing back the cover on the

tank, make sure that is closed correct.

Otherwise there will no pressure be

build up.

Put the tank back in the housing.

Turn on the unit on the main switch

(located on the back of the unit)

Attention: Never us tap water. (Dan-

ger of calcification). Also do not use

explosive or combustible liquids e.g.

alcohol.

Note: The filter in the tank (item no.

3479) should be fully under pressure,

otherwise no water will be sucked in.

Maintenance and care

Cleaning the chuck

Because of the washer, very little

dirt might enter the handpiece. In

the curse of the time, dirt can ap-

pear and might interrupt the perfor-

mance of the handpiece. Therefore

clean the chuck monthly.

Dismount the chuck

Unscrew the top of the handpiece

while using the tongs key:

Clean the inside and the top of the

handpiece now with a dry brush.

Push the black knob forward to

open the chuck.

Set the first key (see picture below) on

the axle and hold it tight. Screw out the

chuck with the second key, which has

the forefront

The assembly of the clamping device

takes place in reverse order. Make sure

that the clamping device is opened

when assembling it.

Cleaning the chuck

Soak the chuck in white spirit or in a

special fluid for cleaning tools. Clean

the slots of the chuck and the drilling

with a brush or a scrubber.

Rinse off the chuck well and let it dry.

Place a small drop of oil on your thumb

and pointer. Rub both fingers until you

find very little of oil on your fingers.

Now take the chuck and put it between

these two fingers and turn it around.

There should only be a very slight film

of oil on the chuck. It counts: Less is

more than too much

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hadewe SPR3 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hadewe SPR3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info