Bedienungsanleitung Hama 20301 - Easytip Z3 Universal Zapper (Seite 2 von 4) (Englisch)

607800

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Deutsch

Code scan Function

If programming using the direct codes failed to operate your TV, VCR or

Satellite then please use the automatic code scan which often finds compatible

codes from other brands or other models within your brand.

A. Switch on your TV SET. When scanning for a VCR code, switch on the

video recorder and start playing a videotape (i.e. start the play function on

the VCR).

B. Set the disk to position and press the key on your remote control

(for approx. 4 seconds) until the LED flashes twice.

C. Enter code 1 1 1 1 (i.e. press ). The LED flashes twice.

D. Press and hold the key until your TV SET is switched off. This

procedure might take up to 15 minutes (when searching for a VCR code,

press and hold the key and not the key).

E. If the device responds by going into standby or the VCR tape stops then

immediately remove your finger from the relevant key and immediately

press the key, this will store the found code into the remote and the LED

flashes twice.

F. When using the Automatic mode it is possible that the remote will find

several codes that appear to work although these might not give 100%

compatibility. If this happens then restart the Automatic mode and move

onto the next code. Please be patient as it might be necessary to scan

through many different codes until a suitable one is found.

Code scan for VCR or SAT

To complete a code scan for VCR or SAT, proceed as described for a TV code

scan. Set disk to position or respectively and complete the above

steps A to F.

At step D, press the key for SAT and the key for VCR.

Reading of currently set code

If you have programmed your remote control by means of a code scan, or if

you do not remember the code you have entered, you have the option to read

the currently used code.

A. Set the disk to position and press the key on your remote control

(for approx. 4 seconds) until the LED flashes twice.

B. Enter code 1 1 1 2 (i.e. press ). The LED flashes twice.

C. Press the key and count the number of LED flashes. This number

corresponds to the first digit of the code.

D. Press the key and count the number of LED flashes. This number

corresponds to the second digit of the code.

E. Press the key and count the number of LED flashes. This number

corresponds to the third digit of the code.

F. Press the key and count the number of LED flashes. This number

corresponds to the fourth digit of the code.

G. Steps C, D, E and F can be repeated as often as necessary.

To read the currently used VCR or SAT code, proceed as described above for

your TV SET. Set disk to position or respectively and complete the

above steps A to G.

Write down the code number as indicated by the LED.

SAT

VCR

▲

SAT

VCR

▲

USER MANUAL

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hama 20301 - Easytip Z3 Universal Zapper Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hama 20301 - Easytip Z3 Universal Zapper

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info