Zoom out
Zoom in
Vorherige Seite
1/4
Nächste Seite
1
Deutsch
UNIVERSAL REMOTE CONTROL
Thank you for purchasing this universal remote control. Before using the
remote you will need to insert 2 type "AAA" batteries (not included) in the
battery compartment ensuring that you follow the polarity shown on the inside.
You can now use your remote control to operate up to 9 different devices
(depending on the model) including a TV, video recorder, DVD player, satellite or
cable receiver, CD player, tuner (radio), tape recorder and amplifier. If your
remote control is equipped with an AUX key (not standard on all models) then
you can also use it to control a second TV set, video recorded, satellite receiver
and/or cable box, CD player, tuner, tape recorder or amplifier!
Easy programming for the control of your TV SET
1. Insert 2 new 1.5V alkaline batteries of type "AAA/LR03". Observe battery
polarity as indicated in the battery compartment.
2. Switch on your TV SET.
3. In the enclosed code list, find your TV brand or manufacturer (e.g. Sony).
4. Beside the manufacturer's name, you will find one or more 3-digit codes.
These codes must be entered into the remote to enable it to work with your
particular TV set.
5. Press the key on the remote control for approximately 4 seconds until
the LED flashes twice.
6. After seeing the 2 flashes and within 5 seconds, enter the 3-digit numerical
code from the list.
7. After entering the code the LED will flash twice indicating that the code has
been accepted.
8. Point the remote control towards your TV and press the key. If your TV
does not respond by going into Stand-By mode then repeat steps 3 to 8
and enter the next code in the list.
9. If your TV goes into Stand-By mode when the key pressed then your
remote control has found a compatible code. Next test all of the other
function buttons. If certain functions are not working correctly then restart
the process moving onto the next code number as this may well improve
the situation.
10. If the codes in the list fail to operate your TV then next move onto the
automatic code scan function (see below).
Easy programming for the control of your VIDEO
RECORDER
To programme the remote control to operate your VIDEO RECORDER, proceed
as described above for the television set. Complete steps 1 to 10 using the
key on your remote control. Please ensure that you refer to the codes
listed under the VIDEO RECORDER section and not the TV section.
Easy programming for the control of your SATELLITE
RECEIVER
To programme the remote control to operate your SATELLITE RECEIVER or
CABLE BOX, proceed as described for the television set. Complete steps 1 to
10 using the key on your remote control. Please ensure that you refer to
the codes listed under the SATELLITE section and not the TV section.
Easy programming for the control of your DVD PLAYER
To programme the remote control to operate your DVD PLAYER, proceed as
described for the television set. Complete steps 1 to 10 using the key on
your remote control. Please ensure that you refer to the codes listed under the
DVD section and not the TV section.
Easy programming for the control of your CD PLAYER
To programme the remote control to operate your CD PLAYER, proceed as
described for the television set. Complete steps 1 to 10 except you must first
press and release the key followed by holding down the key. Please
ensure that you refer to the codes listed under the CD section and not the TV
section.
CD
SHIFT
DVD
SAT
VCR
TV
USER MANUAL
GB
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Inhalt der Seiten


  • Page 1

    GB

    USER
    Deutsch
    MANUAL

    UNIVERSAL REMOTE CONTROL
    Thank you for purchasing this universal remote control. Before using the
    remote you will need to insert 2 type "AAA" batteries (not included) in the
    battery compartment ensuring that you follow the polarity shown on the inside.
    You can now use your remote control to operate up to 9 different devices
    (depending on the model) including a TV, video recorder, DVD player, satellite or
    cable receiver, CD player, tuner (radio), tape recorder and amplifier. If your
    remote control is equipped with an AUX key (not standard on all models) then
    you can also use it to control a second TV set, video recorded, satellite receiver
    and/or cable box, CD player, tuner, tape recorder or amplifier!

    Easy programming for the control of your TV SET

    1. Insert 2 new 1.5V alkaline batteries of type "AAA/LR03". Observe battery
    polarity as indicated in the battery compartment.
    2. Switch on your TV SET.
    3. In the enclosed code list, find your TV brand or manufacturer (e.g. Sony).
    4. Beside the manufacturer's name, you will find one or more 3-digit codes.
    These codes must be entered into the remote to enable it to work with your
    particular TV set.
    5. Press the TV key on the remote control for approximately 4 seconds until
    the LED flashes twice.
    6. After seeing the 2 flashes and within 5 seconds, enter the 3-digit numerical
    code from the list.
    7. After entering the code the LED will flash twice indicating that the code has
    been accepted.
    8. Point the remote control towards your TV and press the
    key. If your TV
    does not respond by going into Stand-By mode then repeat steps 3 to 8
    and enter the next code in the list.
    9. If your TV goes into Stand-By mode when the
    key pressed then your
    remote control has found a compatible code. Next test all of the other
    function buttons. If certain functions are not working correctly then restart
    the process moving onto the next code number as this may well improve
    the situation.
    10. If the codes in the list fail to operate your TV then next move onto the
    automatic code scan function (see below).

    Easy programming for the control of your VIDEO
    RECORDER

    To programme the remote control to operate your VIDEO RECORDER, proceed
    as described above for the television set. Complete steps 1 to 10 using the
    VCR key on your remote control. Please ensure that you refer to the codes
    listed under the VIDEO RECORDER section and not the TV section.

    Easy programming for the control of your SATELLITE
    RECEIVER

    To programme the remote control to operate your SATELLITE RECEIVER or
    CABLE BOX, proceed as described for the television set. Complete steps 1 to
    10 using the SAT key on your remote control. Please ensure that you refer to
    the codes listed under the SATELLITE section and not the TV section.

    Easy programming for the control of your DVD PLAYER
    To programme the remote control to operate your DVD PLAYER, proceed as
    described for the television set. Complete steps 1 to 10 using the DVD key on
    your remote control. Please ensure that you refer to the codes listed under the
    DVD section and not the TV section.

    Easy programming for the control of your CD PLAYER

    To programme the remote control to operate your CD PLAYER, proceed as
    described for the television set. Complete steps 1 to 10 except you must first
    press and release the SHIFT key followed by holding down the CD key. Please
    ensure that you refer to the codes listed under the CD section and not the TV
    section.

    1



  • Page 2

    GB

    USER
    Deutsch
    MANUAL

    Easy programming for the control of your TUNER
    (RADIO)

    To programme the remote control to operate your TUNER, proceed as
    described for the CD PLAYER but using the TUNER key instead of the CD key.
    Please ensure that you refer to the codes listed under the TUNER section and
    not the CD PLAYER section.

    Easy programming for the control of your TAPE
    RECORDER (TAPE DECK)

    To programme the remote control to operate your TAPE RECORDER, proceed
    as described for the CD PLAYER but using the TAPE key instead of the CD key.
    Please ensure that you refer to the codes listed under the TAPE section and not
    the CD PLAYER section.

    Easy programming for the control of your AMPLIFIER

    To programme the remote control to operate your AMPLIFIER, proceed as
    described for the CD PLAYER. Complete steps 1 to 10, using the AMP key on
    your remote control. Please ensure that you refer to the codes listed under the
    AMPLIFIER section and not CD PLAYER section.

    Code scan

    If programming using the codes in the enclosed list failed to work then you
    must next try the automatic code scan.
    A. Ensure that the remote control is equipped with 2 new batteries (see step
    one of easy programming procedure).
    B. Switch on your TV SET. When using the automatic scan function for the
    VCR, DVD, CD or TAPE, switch on your device, insert a video tape, DVD,
    CD or tape cassette and put the unit into ‘Play mode’ i.e, the VCR tape etc
    is running.
    C. Press the TV key of your remote control for approx. 4 seconds until the
    LED flashes twice.
    D. After seeing the 2 flashes and within 5 seconds, enter the code 0 0 1 .
    After entering the code the LED will flash twice indicating that the code has
    been accepted
    E. Press and hold the
    key until your TV switches off. Please note that this
    process might take up to 15 minutes. During the automatic scanning you
    can remove your finger or change hands provided it is replaced within 8
    seconds. If left off of the key for more than 8 seconds then the remote will
    revert back to its normal mode. If your TV switches into Stand-By mode
    during the automatic process then immediately remove your finger from the
    key and then press and release the TV key until the LED flashes
    twice, this will then store the code that the remote has found
    F. In some cases during the automatic scanning search the remote control
    might find several codes that appear to operate your TV etc, however, if
    some of the buttons fail to work properly then it’s possible the remote has
    found a partially compatible code. In such cases you will need to restart the
    automatic scanning process (steps B. to F.) until a better code is found.
    Please note that once the automatic process is restarted, the remote
    continues from the last stored code and not at the beginning of code
    database.
    • To complete a code scan for the VCR, DVD, CD or TAPE, follow the
    procedure above but use the
    key and not the
    key
    • To complete a code scan for the TUNER, follow the procedure above but
    use the key 2

    2



  • Page 3

    GB

    USER
    Deutsch
    MANUAL

    Code scan for VCR, SAT, DVD, CD, TAPE, TUNER and
    AMP

    To complete a code scan for VCR, SAT, DVD, CD, TAPE, TUNER or AMP,
    proceed as described for a TV code scan. Complete above steps A to G, using
    keys
    VCR / SAT or DVD , or
    SHIFT and CD / SHIFT and TAPE / SHIFT and TUNER or SHIFT and AMP respectively.
    At step E,
    for SAT and AMP, press the
    key;
    for VCR, DVD, CD and TAPE, press the
    key, and
    for TUNER, press key 2 .

    Finding out what code number you are using

    If you have programmed your remote control by means of the automatic code
    scan, or if you have forgoten the code you have stored then the following
    procedure will replay the codes being used.
    A. Press the TV key of your remote control for approx. 4 seconds until the
    LED flashes twice.
    B. Enter code 0 0 2 , using the numerical keys. The LED flashes twice.
    C. Press key 1 and count the number of LED flashes. This number
    corresponds to the first digit of the code.
    D. Press key 2 and count the number of LED flashes. This number
    corresponds to the second digit of the code (if the digit is 0, the LED does
    not flash).
    E. Press key 3 and count the number of LED flashes. This number
    corresponds to the third digit of the code (if the digit is 0, the LED does not
    flash).
    F. Steps C, D and E can be repeated as often as necessary.
    To read the currently used code for the control of a VCR, SAT, DVD/AUX, CD,
    TAPE, TUNER or AMP device, proceed as described above for your TV SET.
    Complete steps A to F, pressing the VCR , SAT , DVD , CD , TAPE , TUNER or AMP
    key respectively.
    Write down the code number as indicated by the LED.

    Programming for AUX devices

    If the remote you have purchased has a separate AUX key then this can be
    used to operate a second TV set, video recorder, satellite receiver/cable box,
    CD player, tape recorder, tuner or amplifier. To program your remote
    control for a second device, proceed as follows:
    1. Press the AUX key of your remote control until the LED flashes twice.
    2. Press
    TV
    key for a second TV set,
    VCR key for a second video recorder,
    SAT key for a second satellite receiver or cable box,
    keys SHIFT and CD for a second CD player,
    keys SHIFT and TAPE for a second tape recorder,
    keys SHIFT and TUNER for a second tuner,
    keys SHIFT and AMP for a second amplifier.
    3. On the numerical keypad, enter a 3-digit code from the enclosed list.
    4. The LED flashes twice, indicating that the code has been accepted.

    3



  • Page 4

    GB

    USER
    Deutsch
    MANUAL

    Special functions of your remote control

    Brightness / Colour / Contrast / etc.
    Adjusting brightness / colour / contrast / bass / tremble / balance at your TV
    set, using the universal remote control:
    1. Ensure that your remote control is set to TV (press TV key).
    2. Press the SHIFT key.
    3. Within 5 seconds, press
    1 for brightness,
    2 for colour,
    3 for contrast,
    4 for tremble,
    5 for bass,
    6 for balance.
    4. To adjust the settings use the VOL+ and VOL- keys.
    5. After 5 seconds, your remote control returns to standard mode for the
    selection of channels.

    OK key

    • At TV level The basic settings of your TV SET are activated
    • At TV level / menu Confirmation key for settings
    • At VCR level Record button (press key twice)
    • At SAT level Confirmation key for settings
    • At DVD level Confirmation key for settings
    • At TAPE level Record button (press key twice)
    Please write down the 3-digit codes of your devices for future reference.
    Depending on the remote control model, you might have to reprogram me
    the universal control device after a battery change.

    TV
    VCR
    SAT
    DVD/AUX
    CD
    TAPE
    TUNER
    AMPLIFIER

    4






Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hama 20312 - Easytip S9 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Holen Sie sich Ihr Benutzerhandbuch per E-Mail

Geben Sie Ihre E-Mail-Adresse ein, um das Handbuch zu erhalten von Hama 20312 - Easytip S9 in der Sprache / Sprachen: Englisch als Anhang in Ihrer E-Mail.

Das Handbuch ist 0,09 mb groß.

 

Sie erhalten das Handbuch in Ihrer E-Mail innerhalb von Minuten. Wenn Sie keine E-Mail erhalten haben, haben Sie wahrscheinlich die falsche E-Mail-Adresse eingegeben oder Ihre Mailbox ist zu voll. Darüber hinaus kann es sein, dass Ihr ISP eine maximale Größe für E-Mails empfangen kann.

Andere Handbücher von Hama 20312 - Easytip S9

Hama 20312 - Easytip S9 Bedienungsanleitung - Deutsch - 4 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info