Bedienungsanleitung Harman Kardon AVR 151 (Seite 5 von 47) (Englisch)

534560

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

ENGLISH

AVR

Front-Panel Controls

Front-Panel Controls, continued

Power indicator/Power button: The AVR has three different power modes:

OffŘ (Power indicator glows solid amber): The Off mode minimizes energy consumption

when you’re not using the AVR. When the AVR is off, it will not automatically turn on

or play audio in response to a DLNA DMR stream from a networked device. When

the AVR is off, pressing the Power button turns it on. To turn the AVR off when it is on,

press the Power button for more than three seconds. The Front-Panel Display will

indicate “Your device is switched off” for two seconds, then will switch off.

NOTE: You can use the System Setup menu to set the AVR to automatically enter

the off mode after it has been in the Sleep mode for a certain period of time. See

System Settings, on page 29.

Sleep Ř (Power indicator glows solid amber and front-panel display indicates “Device

sleep”): The Sleep mode powers-down some of the AVR’s circuitry, but allows the

AVR to automatically turn on and play audio in response to a DMR stream from a

networked device. When the AVR is in Sleep, pressing the Power button turns it on.

To put the AVR into Sleep when it is on, press the Power button for less than three

seconds. The front-panel display will indicate “Your device is going to sleep” and

then indicate “Device sleep” while the AVR is in the Sleep mode.

NOTE: The AVR will automatically enter the Sleep mode after 30 minutes of no audio

signal or user control input, unless USB, iPod, Home Network, vTuner or DLNA DMR

is active. In these cases, the AVR will automatically enter the Sleep mode after the

number of hours set in the Auto Power Off system setting. See System Settings,

on page 29.

On Ř (Power indicator glows solid white): When the AVR is on it is fully operational.

Headphone jack: Connect a 1/4" stereo headphone plug to this jack for private

listening.

Tuning Mode button (AVR 1510 only): Press this button to toggle the radio between the

manual (one frequency step at a time) and automatic (seeks frequencies with acceptable

signal strength) FM tuning mode. The button also toggles the radio between stereo and

mono modes when an FM station is tuned in.

RDS button (AVR 151 only): When listening to an FM radio station that broadcasts RDS

information, this button activates the various RDS functions.

USB port: The USB port can be used to play audio ﬁles from an Apple iOS

device

connected to the port, and can also be used to play MP3 and WMA audio ﬁles from a USB

device inserted into the port. Insert the connector or device into the USB port oriented so

it ﬁts all the way into the port. You may insert or remove the connector or device at any

time – there is no installation or ejection procedure.

You can also use the USB port to perform ﬁrmware upgrades. If an upgrade for the AVR’s

operating system is released in the future, you will be able to download it to the AVR

using this port. Complete instructions will be provided at that time.

IMPORTANT: Do not connect a PC or other USB host/controller to this port, or you

may damage both the AVR and the other device.

Channel Volume Adjust button: Press this button to activate the individual channel

level adjustment. After pressing this button, use the Up/Down buttons/Tuning buttons to

select the channel for adjustment and use the Left/Right buttons to adjust the channel’s

level.

Audio Input button: Press this button to change the audio input connection for the current

source. Use the Left/Right buttons to cycle through the available input connections, and

press the Set button to assign the currently-displayed connection to the source.

IR sensor: This sensor receives infrared (IR) commands from the remote control. Make

sure that the sensor is not blocked.

Set button: Press this button to select the currently highlighted menu item.

Left/Right buttons: Use these buttons to navigate the AVR’s menus.

Front-panel display: Various messages appear on this two-line display in response to

commands and changes in the incoming signal. In normal operation, the current source

name appears on the upper line, while the active surround mode is displayed on the

lower line. When the on-screen display menu system (OSD) is in use, the current menu

settings appear.

Up/Down buttons/Tuning buttons: Use these buttons to navigate the AVR’s menus.

When the radio is the active source, use these buttons to tune stations according to the

setting of the Tuning Mode button (see above).

Surround Mode Category button: Press this button to select a surround-sound category.

Each press changes the surround-mode category: Auto Select, Virtual Surround, Stereo,

Movie, Music and Game. To change the speciﬁc surround-sound mode within the

category, use the Surround Mode Select buttons. See Audio Processing and Surround

Sound, on page 27, for more information about surround modes.

Surround Mode Select buttons: After you have selected the desired surround-mode

category, press these buttons to select a speciﬁc mode within the category, such as to

change from Dolby

Pro Logic

II Movie mode to DTS

NEO:6 Cinema mode. Surround

mode availability depends on the nature of the source input signal, i.e., digital versus

analog, and the number of channels encoded within the signal.

Source Select buttons: Press these buttons to select the active source.

Volume knob: Turn this knob to raise or lower the volume.

Harman Kardon AVR 151 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR 151

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info