Bedienungsanleitung Health-Mor Defender (Seite 4 von 9) (Englisch)

626342

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

Operating Instructions:

❶

 Plug unit into outlet. (Green indicator located on the power

On/Off

switch will

illuminate, indicating that the unit has power and not that the unit is turned

❷

 Press power

On/Off

switch to the

On (“I”)

position. When the unit is turned on initially,

all indicators located on the front panel will illuminate for two seconds. The green

Power On

Indicator

(leaf) will illuminate and remain lit as long as the unit’s power

switch is in the

(“I”)

position.

❸

 The unit will start running at low speed. (Low-Speed Indicator will illuminate.)

❹

 The

and

Down Arrow Buttons

located on the front panel can now be utilized for

speed control as follows:

Down Arrow Button:

Press to decrease motor speed selection (motor speed will

not change if unit is already operating at low speed).

Up Arrow Button:

Press to increase motor speed selection (motor speed will not

change if unit is already operating at high speed).

Caution:

• Liquid or spray scents, aroma therapy oils or other aromatic hydrocarbons with the

Defender

could cause damage to the plastic housing. Damage to the plastic housing could

expose moving parts.

• To reduce the risk of injury from moving parts. Do not use with liquid or spray scents,

aroma therapy oils or other aromatic hydrocarbons.

• Use of these substances will void your warranty.

Programming Instructions:

Program mode allows you to set and activate a 24 hour continuous operation program loop.

To Initiate Program Mode:

❶

 Turn off unit.

❷

 Press and hold the

Down Arrow Button

while turning on unit.

❸

 Once the green

High-Speed Indicator

starts flashing, release the

Down Arrow

Button.

The unit is now in program mode. Follow the instructions below to set your

desired program sequence.

To Set a Program Sequence:

The motor speed must be set in twelve consecutive two-hour increments totaling 24 hours

of operation.

Program Sequence Start Time: The sequence will begin its cycle with the first two-hour

increment immediately after the twelfth two-hour increment is programmed. Please be sure to

consider the program sequence start time when planning your desired program sequence. (If it

is now 2 PM, the first increment will start here.)

❶

Plan your desired program sequence using the table on page 5.

❷

Select the desired motor speed for the first two hours of operation by pressing the

Down

Arrow Button.

(High speed is currently selected. Press the

Down Arrow Button

once

to select medium speed, twice to select low speed, and three times to select motor off.)

❸

Once you’ve selected the motor speed for the first two-hour time increment, press the

Arrow Button

to lock in the speed. (After each two-hour speed selection has been locked

in, the red

Filter Replacement Indicator

will f lash.)

❹

Continue to set each consecutive two-hour increment by selecting the speed with the

Down Arrow Button

and then locking in each selection with the

Up Arrow Button.

Operation

Up Arrow Button

High-Speed Indicator

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Health-Mor Defender Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Health-Mor Defender

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info