Bedienungsanleitung Hifonics Gladiator (Seite 4 von 16) (Englisch)

505734

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

AMPLIFIER FEATURE DESCRIPTIONS

GLADIATOR AMPLIFIERS:

A POWER LED indicates the powered up and turned on condition.

Each model is capable of 4 & 2-Ohms stereo per channel, or 4-Ohms mono bridged operation except

All Hifonics amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit,

the mono amps which are capable of 4, 2 and 1-Ohm loads.

and amplifier DC faults indicated by the red “PROTECT” LED.

Tri-Mode operation with any stereo pair of amplifier channels is possible, as with all bridgeable

CAUTION: DO NOT OPERATE ANY AMPLIFIER BELOW THE INTENDED IMPEDANCE. YOU

amplifiers.

The input sensitivities for rated output powers are variable from 0.2V to 6V for the multi channel

WILL CAUSE DAMAGE TO THE AMPLIFIER THAT WILL NOT BE COVERED UNDER THE

amplifiers and 0.2V to 9V for the mono models.

WARRANTY PRINTED IN THE BACK OF THE MANUAL. 2 & 4 Channel amps are capable of 4

All crossovers are fully variable in their respective ranges.

and 2-Ohms wired stereo and 4-Ohms wired mono bridged. The mono amps are capable of 4, 2

Crossover filters are 12dB/Octave.

and 1-Ohm.

SUBSONIC: Crossover filter from 15Hz to 35Hz.

LOW PASS: Crossover filter from 30Hz to 250Hz.

LEVEL: Adjusts the input sensitivity from 0.2 volts to 9 volts.

BASS EQ: Adjustable bass boost from 0db to 10dB.

PHASE:

REMOTE: This is the input jack for the remote Level control.

BALANCED INPUT:

LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 9V.

LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy

chain multiple amplifiers from one signal.

The Phase Shift is fully adjustable from 0 to 180 degrees and this allows you to control time

alignment.

Accepts line level balanced input from 0.4v to 18v.

-The LINE INPUT signal is routed directly to the LINE OUT RCA jacks, and not affected by the

settings on the amplifier simplifying daisy chaining of amplifiers.

SUBSONIC: Crossover filter from 15Hz to 35Hz.

LOW PASS: Crossover filter from 30Hz to 250Hz.

LEVEL: Adjusts the input sensitivity from 0.2 volts to 9 volts.

BASS EQ: Adjustable bass boost from 0db to 10dB.

PHASE:

REMOTE: This is the input jack for the remote Level control.

BALANCED INPUT:

LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 9V.

LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy

chain multiple amplifiers from one signal.

The Phase Shift is fully adjustable from 0 to 180 degrees and this allows you to control time

alignment.

Accepts line level balanced input from 0.4v to 18v.

-The LINE INPUT signal is routed directly to the LINE OUT RCA jacks, and not affected by the

settings on the amplifier simplifying daisy chaining of amplifiers.

The BRE2500.1D is a linkable amplifier and features a MASTER / SLAVE selection switch and IN /

OUT RCA connection.

The mono amps are capable of 4, 2 & 1-Ohm loads.

Operating the amp below 1-Ohm can cause damage to the

amp not covered in the warranty.

The mono amps are capable of 4, 2 & 1-Ohm loads.

Operating the amp below 1-Ohm can cause damage to the

amp not covered in the warranty.

GLX1000.1D / GLX1400.1D / GLX1800.1D MONO BLOCK AMPLIFIERS

GLX2200.1D MONO BLOCK AMPLIFIERS

The 4 channel amps have the same features as the 2 channel models accept that there are 2 sets of

controls.

1 set for channels 1 & 2 and 1 set for channels 3 & 4.

In addition, the 4 channel models have a Mode switch which allows you to select 2 or 4 channel

operation. Switch to 2 channel if you only have 1 set of RCA’s in CH 1/2 and the unit will automatically

supply signal to channels 3/4. Select 4 channel if you are providing RCA’s to channels 1/2 and 3/4.

The X-OVER slide switch selects the internal crossover functions:

-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting

simplifying daisy chaining of amplifiers.

-HI: Selects the built in HI PASS filter.

-FULL: Bypasses all crossovers for full frequency range operation.

-LP/BP: Selects the built in LOW PASS filter.

LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.

LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy

chain multiple amplifiers from one signal.

HI PASS: Variable low frequency cut off from 10Hz to 15kHz.

LOW PASS: Variable high frequency cut off from 30Hz to 150Hz.

BASS EQ: 45Hz bass boost variable from 0dB to 10dB.

LEVEL: Variable LEVEL (GAIN) control from 6.0V to 0.2V.

Note that the LOW PASS signal is MONO.

-In the LP/BP position, the HI PASS filter acts as a subsonic

filter.

-When the LP/BP mode is selected, a 0 to +10dB, at 45Hz,

BASS EQ is also switched in.

GLX60.4 / GLX100.4 4-CHANNEL AMPLIFIERS

CH1/2 CH3/4 REMOTE HI PASS CH1/2 X-OVER LOW PASS BASS EQ LEVEL POWER LINE OUTPUT

10Hz 15kHz 30Hz 150Hz 0dB 10dB 6.0V 0.2V

LINE INPUT MODE HI PASS CH3/4 X-OVER LOW PASS BASS EQ LEVEL

PROTECT

2CH 4CH

HI FULL LP/BP

INPUT OUTPUT INPUT LEVEL PHASE REMOTE BASS EQ SONIC LOW PASS

L L

R R

SUB

POWER

PROTECT

BALANCED

9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz

INPUT OUTPUT INPUT LEVEL PHASE REMOTE BASS EQ SONIC LOW PASS

L L

R R

SUB

OUT

POWER

PROTECT

OUTPUT

MASTER

INPUT

SLAVE

BALANCED

9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz

Hifonics Gladiator Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info