168839
16
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
Speaker & RCA Connections
TXi 1700
Subwoofer with Dual-Voice-Coil 2 Subwoofers with Single-Voice-Coil
Subwoofer with Single-V
oice-Coil 1 - 8 Ohms
Subw
ofer w
th D
al-Voic
oi 1 - 8 Oh
s per V
oi
e-Co lo
i u
e-C
l m c
i
SET-UP MASTER-Amp
MODE - Schalter
• Switch to the "LP or FULL”-position.
PHASE
FREQ RANGE
Q-Control
SUB BOOST
BASS REMOTE
SUB SONIC
LOW PASS
LEVEL
Attend regarding notes on page 14 if you use
LOW PASS-MODE or on page 15 if you
use FULL-MODE.
Caution!
Do not connect speaker (-) to the ground or vehicle's chassis.
MASTER/SLAVE-MODE / Subwoofer-Mode with two Ampifiers
• Connect the "LINE IN" (L & R) of the MASTER-amplifier to the head unit´s line output with appropriate good quality RCA cables.
• Connect the "SLAVE OUT" RCA Output of the MASTER-Amp with the "LINE IN" RCA Input of the SLAVE-AMP.
• Connect the "REMOTE"-Terminal of the MASTER-Amp with the supplied BASS REMOTE.
• Connect the "REMOTE"-Wire of your head unit with the REM-Terminals of both Amplifiers.
• Connect the subwoofer with appropriate wires to the terminal block (SPEAKER OUTPUT - and +) of both amplifiers. As optional feature an
additonal Subwoofer can be connected to the non-occupied terminals.
• Connect the Protect/Bridge Connection of the Master with the Protect/Bridge Connection of the Slave.
This connection warrants if there is an operation fault both amps, Master and Slave, would go into protection mode so the amps are prevented
for any possible damages.
• The minimum final subwoofer impedance must not be lower than 2 Ohms in total (1 Ohm for each Amplifier) or 2 Ohms bridged. Too low speaker
loads result in too high heat dissipation and may cause the amplifier run into protection.
• Please observe correct speaker channels and polarity as printed by the speaker terminal.
SET-UP SLAVE-Amp
MODE - Switch
• Switch to the "SLAVE”-position.
PHASE
FREQ RANGE
Q-Control
SUB BOOST
BASS REMOTE
SUB SONIC
LOW PASS
LEVEL
All controllers are in this operation mode without function.
Only the output signal of the Master-Amp will be amplified.
MASTER
SLAVE
0dB 18dB
Connect Master´s Protect/Bridge
with Slave´s Protect/Bridge
Subwoofer
1 - 8 Ohm
Bass Remote Control - connection for remote control.
This contoller regulates the bass level from e.g. the driver's seat.
+
-
+
-
SPEAKER OUTPUT
MASTER
SPEAKER OUTPUT
SLAVE
SPEAKER OUTPUT
MASTER
SPEAKER OUTPUT
SLAVE
+
-
+
-
h
i
.Caution: Please observe t e r ght polarity
. Slave´s - to Loudspeaker´s + and Slave´s
+ to Loudspeaker´s -
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hifonics txi 1700 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info