167658
20
Zoom out
Zoom in
Vorherige Seite
1/24
Nächste Seite
18
20
Connect RCA outputs (CH1/2
and CH3/4) of the head unit with
LINE INPUT (CH1/2 and CH3/4)
of the amplifier.
Subwoofer 2
4 - 8 Ohm
X-Over-Switch (CH1/2 Subwoofer 1 & CH3/4 Subwoofer 2)
• By using the Mono/Subwoofer-mode, switch to the LP/BP-position (LOW PASS/BAND PASS), that the higher frequencies are
cut off. The cut-off frequency should be between 60Hz - 100Hz. Adjust the level with the LO PASS-controller. In LP/BP-Mode
the Highpass-controller (HI PASS) is working also as Subsonic-Filter. The Subsonic frequency should be between 15Hz - 40Hz,
depending on the size of the installed subwoofer.
Input Level (CH1/2 Subwoofer 1 & CH3/4 Subwoofer 2)
• Turn the LEVEL control of the amplifier to 6V position.
• Turn the head unit volume control to about 80 - 90% of its full setting.
• Turn the LEVEL control clockwise until you hear some distortion.
• Then turn back the LEVEL control slightly until you can hear a clean sound.
Bass EQ (CH1/2 Subwoofer 1 & CH3/4 Subwoofer 2)
• This Controller regulates the Bass Boost from 0 - 18 dB.
Caution! Please use the Bass-EQ carefully. The additional boost may result in clipping or overload.
Bass Remote (CH3/4 Subwoofer 2)
• The provided Bass Remote regulates the Bass Level of CH3/4 from e.g. the driver's seat.
Bass Remote Control -
Connection for remote
control. This Contoller
regulates the Bass Level
from f.i. the driver's seat.
Speaker & RCA Connections
ZXi 4400 / ZXi 6400 / ZXi 9400
3-Channel-Mode 2 Mono Subwoofer bridged
RCA & Speaker wiring:
• Connect the LINE INPUT of the amplifier to the head unit line output with appropriate good quality RCA cables.
• Connect the speakers/subwoofer with appropriate wires to the terminal block (SPEAKER OUTPUT/ - CH1/2 - Mono bridged +
and the subwoofer with CH3/4 - Mono bridged +) of the amplifier.
• The minimum final subwoofer impedance must not be lower than 4 Ohms per channelpair. Too low speaker loads result in too
high heat dissipation and may cause the amplifier run into protection.
• Please observe correct speaker channels and polarity as printed by the speaker terminal
Caution!
Do not connect speaker (-) to the ground or vehicle's chassis.
ZXi 4400 MkII
4 x 150 Watts
e13
021584
FUSE
GND REM BATT+ 12V
POWER INPUT
SPEAKER OUTPUT
+ CH3 + CH4
+ MONO BRIDGED –
+ CH1 + CH2
Subwoofer 1
4 - 8 Ohm
20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hifonics zxi 9000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info