Bedienungsanleitung Hitachi dv 10 dva (Seite 28 von 32) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

387422

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

English

100

10°C

20°C

NOTE

The charging time may very depending on the

ambient temperature and input power supply

voltage conditions.

The example of the relationship between the input

power supply voltage and the charging time is shown

in Fig 9.

The charging time decreasaes if the ambient

temperature and input power supply voltage are

high and increases when they are low.

Fig.9 Relationship Between Input Power Supply

Voltage and Charging Time

CAUTION

If the battery is heated due to direct sunlight, etc.,

just after operation, the charger pilot lamp may

not light. At that time cool the battery first, then

start charging.

3. Disconnect the charger power cord from the AC

outlet.

4. Hold the charger tight and pull out the battery.

PRIOR TO OPERATION

1. Setting up and checking the work environment

Check if the work environment is suitable by fol-

lowing the precautions.

HOW TO USE

1. Confirm the cap position

The three modes of screwdriver, drill and impact drill

can be switched by the position of the cap in this tool.

(1) When the tool is used as a screwdriver, align the

number displayed on the cap from "1" to "5" to the

triangle mark of the housing.

(2) When the tool is used as a drill, align the drill mark

" displayed on the cap to the triangle mark of

the housing.

(3) When the tool is used as the impact drill, align the

hammer mark "

" displayed on the cap to the

triangle mark of the housing. (See Fig. 4.)

3. Minus driver bit

a Screw size

0.8 mm 4 mm

4. Hexagon socket (for nuts and bolts)

Socket No. Screw size

74 mm

85 mm

10 6 mm

Socket No.

5. Drill bit for brick

Diameter, 6.5 mm, 8 mm, 9.5 mm, 10 mm

Optional accessories are subject to change without notice.

APPLICATIONS

⅜ Drilling of brick and concrete block, etc.

⅜ Driving and removing of machine screws, wood

screws, tapping screws, etc.

⅜ Drilling of various metals.

⅜ Drilling of various woods.

BATTERY REMOVAL/INSTALLATION

1. Battery removal

Hold the handle tightly and push the battery latch

to remove the battery (see Figs. 1 and 2).

CAUTION

Never short-circuit the battery.

2. Battery installation

Insert the battery while observing its polarities (see

Fig. 2).

CHARGING

Before using the impact drill, charge the battery as

follows.

1. Insert the battery in the charger.

Position the battery so that the nameplate faces

toward the nameplate of the charger and press in

the battery until it comes into contact with the

bottom plate. (See Figs. 1 and 3.)

2. Connect the charger power cord to the AC outlet.

Connecting the power cord will turn on the charger

(the pilot lamp lights up).

CAUTION

If the pilot lamp does not light up, pull out the

power cord from the AC outlet and check the

battery mounting condition.

About 1 hour is required to fully charge the battery

at a temperature of about 20°C. The pilot lamp goes

off to indicate that the batterry is fully charged.

(Minutes)

95% of Rated

Voltage

105% of

Rated Voltage

(Voltage Listed

on Nameplate)

Charging time

Input Power Supply Voltage

Ambient temperature

Battery: EB12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi dv 10 dva Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info