Bedienungsanleitung Hitachi H 70 SD (Seite 5 von 41) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

78772

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

English

PARTICULAR PRECAUTIONS ON USING

DEMOLITION HAMMER

1. Wear ear protectors

Exposure to noise can cause hearing loss.

2. Use auxiliary handles supplied with the tool.

Loss of control can cause personal injury.

3. Do not touch the bit during or immediately after

operation. The bit becomes very hot during operation

and could cause serious burns.

SPECIFICATIONS

Voltage (by areas)* (110V, 230V, 240V)

Power Input 1240W*

Full-load Impact Rate 1400min

–1

(/min)

Weight (without cord, side handle) 20 kg

* Be sure to check the nameplate on this Demolition Hammer as it is subject to change by areas.

4. Before starting to break, chip or drill into a wall, floor

or ceiling, thoroughly confirm that such items as

electric cables or conduits are not buried inside.

5. Properly set the bit holder

6. At the start of work, confirm screw tightening.

7. When working at a highly elevated location, pay

attention to articles and persons below.

8. Wear protective shoes to protect your feet.

STANDARD ACCESSORIES

(1) Case ............................................................................. 1

Standard accessories are subject to change without

notice.

OPTIONAL ACCESSORIES (sold separately)

⅜ Asphalt Cutting

⅜ Groove Digging and Edging

⅜ Crushing

⅜ Scooping Work

⅜ Grease

500g (in a can)

70g (in a tube)

30g (in a tube)

Optional accessories are subject to change without notice.

(1) Cutter

Overall Length: 410, 520 mm

Width: 75 mm

(1) Scoop

Overall Length: 546 mm

(1) Bull Point

Overall Length: 410 mm

(1) Cold Chisel

Overall Length: 410, 520 mm

APPLICATIONS

This Demolition Hammer should be applied to

demolishing concrete, chiseling off concrete, grooving,

bar cutting installation of piping and wiring, sanitary

facility installation, machinery installation, water supply

and drainage work, interior jobs, harbor facilities and

other civil engineering works.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate of this Demolition Hammer.

2. Power switch

Ensure that the power switch is in the OFF position. If

the plug is connected to a receptacle while the power

switch is in the ON position, this Demolition Hammer

will start operating immediately, which could cause a

serious accident.

3. Extension cord

When the work area is remote from the power source,

use an extension cord of sufficient thickness and

rated capacity. The extension cord should be kept as

short as practicable.

4. Mounting an accessory, such as a bull point, a cutter,

etc.

CAUTION:

Be sure to switch OFF and disconnect the attachment

plug from the receptacle to avoid a serious accident.

NOTE:

For accessories such as a bull point and a cutter, use

only Hitachi genuine parts.

* It is possible to attach an accessory, such as a bull

point, a cutter, etc., with any of the three types of

the accessory shank portion shapes shown below.

Air Tool Shank Bit

01Eng_H70SD_WE 4/19/07, 14:554

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi H 70 SD Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info