Bedienungsanleitung Hitachi H90SC (Seite 5 von 32) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

511990

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

English

Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V)

Input* 1450W

Full-load impact rate 850/min.

Weight (without cord) 32 kg

SPECIFICATIONS

* Be sure to check the nameplate on this Demolition Hammer as it is subject to change by areas.

DEMOLITION HAMMER SAFETY WARNINGS

1. Wear ear protectors.

Exposure to noise can cause hearing loss.

2. Use auxiliary handles supplied with the tool.

Loss of control can cause personal injury.

3. Do not touch the bit during or immediately after

operation. The bit becomes very hot during operation

and could cause serious burns.

4. Before starting to break, chip or drill into a wall, floor

or ceiling, thoroughly confirm that such items as

electric cables or conduits are not buried inside.

5. Properly set the bit holder

6. At the start of work, confirm screw tightening.

7. When working at a highly elevated location, pay

attention to articles and persons below.

8. Wear protective shoes to protect your feet.

STANDARD ACCESSORIES

(1) Hexagon Bar Wrench for M12 .................................. 1

(2) Hexagon Bar Wrench for M6 .................................... 1

(3) Hexagon Bar Wrench for M4 .................................... 1

(4) Side Handle ................................................................ 1

(5) Bolt .............................................................................. 4

Standard accessories are subject to change without

notice.

OPTIONAL ACCESSORIES

(sold separately)

1. Bull point

Total length: 410, 520 mm

2. Cold chisel

Total length: 520 mm

3. Scoop

Total length: 546 mm

4. Cutter

Total length: 520 mm

Width: 75 mm

5. Rammer + Shank

Total length: 520 mm

Outer diameter: 200 mm

6. Hammer grease 500g (in a can)

Optional accessories are subject to change without notice.

APPLICATIONS

This Demolition Hammer should be applied to

demolishing concrete, chiseling off concrete, grooving,

bar cutting installation of piping and wiring, sanitary

facility installation, machinery installation, water supply

and drainage work, interior jobs, harbor facilities and

other civil engineering works.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate of this Demolition Hammer.

2. Power switch

Ensure that the power switch is in the OFF position. If

the plug is connected to a receptacle while the power

switch is in the ON position, this Demolition Hammer

will start operating immediately, which could cause a

serious accident.

3. Extension cord

When the work area is remote from the power source,

use an extension cord of sufficient thickness and

rated capacity. The extension cord should be kept as

short as practicable.

4. Mounting an accessory, such as a bull point, a cutter,

etc.

(1) With the retainer directed backward, insert the

accessory shank portion into the hole on the front

cover. (Fig. 1)

01Eng_H90SC_WE 08/12/10, 17:054

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi H90SC Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info