Bedienungsanleitung Hitachi m 8 (Seite 29 von 34) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

427018

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

English

3. Model M12V(S), M12SA(S), M8V(S), M8(S)

(1) Template Guide

(2) Dust Collector Set (Fig. 27

)

(3) Fine Adjustment Knob (Fig. 27

]

)

Optional accessories are subject to change without notice.

APPLICATIONS

⅜ Woodworking jobs centered on grooving and

chamfering.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position. If

the plug is connected to a power receptacle while the

power switch is in the ON position, the power tool will

start operating immediately, inviting serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be kept

as short as practicable.

4. Setting the attachment angle of the handle:

As Fig. 1 shows, the handle attachment angle can be

set in three stages. Use a Plus-head screwdriver to

loosen the machine screw attached to the handle

adjust the handle to the desired position and re-

tighten the machine screw.

MOUNTING AND DISMOUNTING BITS

1. Mounting Bits:

(1) Insert the bit deeply in the collet chuck hole. As shown

in Fig. 2, press the lock plate

, tighten the collet nut

and then use the accessory wrench

to firmly tighten

the collet chuck.

CAUTION

Ensure that the collet chuck is firmly tightened after

inserting a bit. Failure to do so will result in damage to

the collet chuck.

(2) Be sure to use a chuck sleeve when using a 6 mm, 8

mm, 10 mm, 1/4 inch or 3/8 inch bit with Models

M12V(S) or M12SA(S). Also use a chuck sleeve when

using a 6 mm or 1/4 inch bit on a Model M8(S) or

M8V(S) with a collet chuck capacity of 8 mm. First

insert the chuck sleeve deeply in the collet chuck, then

insert the bit in the chuck sleeve. Tighten the collet

chuck firmly as in step (1).

2. Dismounting Bits:

When dismounting the bits, do so by following the

steps for mounting bits in reverse order.

HOW TO USE THE ROUTER

1. Setting the cutting depth:

(1) As shown in Fig. 3, turn the stopper block

so that the

section to which the cut depth setting screw

stopper block

is not attached comes to the bottom

of the stopper pole

. Loosen wing bolt (A)

and turn

knob

to bring stopper pole

in contact with

stopper block

(2) As shown in Fig. 4, loosen the lock lever and press

down the main unit until the bit comes into slight

contact with the surface of the materials. Tighten the

lock lever at this point.

(3) As shown in Fig. 5, loosen wing bolt (B)

. Turning

knob

while pulling it outward will cause scale

move. Pushing it back and turning will cause stopper

pole

to move. Turn knob

while pulling and align

the arrow on stopper pole

to “0” of scale

. Tighten

wing bolt (B)

. This condition is the “0” cutting

depth.

(4) As shown in Fig. 6, turn back knob

and then tighten

the wing bolt (A)

when the arrow on the stopper

pole

indicates the desired cutting depth.

(5) Loosen the lock lever and press the main unit down

until the stopper pole comes in contact with the

stopper block to obtain the desired cutting depth.

(6) The two cut-depth setting screws

attached to the

stopper block can be adjusted to simultaneously set

three different cutting depths. As shown in Fig. 7, use

a wrench to tighten the nuts so that the cut-depth

setting screws

do not come loose at this time.

(7) As shown in Fig. 8 (a), loosening the two nuts

on the

threaded column and moving them down will allow

you to move down to the end position of the bit when

the lock lever was loosened. This is helpful when

moving the router to align the bit with the cutting

position. As shown in Fig. 8 (b), tighten the upper and

lower nuts

to secure the cutting depth.

(8) When you are not using the scale to set the cutting

depth, push up the stopper pole so that it is not in the

way.

2. Guiding the Router

(1) Straight Guide (Model M12V(S), M12SA(S))

Use the straight guide for chamfering and groove

cutting along the materials side. First of all, as shown

in Fig. 9, attach the two wing bolts (A) (M6 × 15)

and

the two lock springs

(both standard accessories) to

the screw holes on the top side of the base. Use the

feed screw

and the wing bolt (C) (M6 × 10)

attach the bar holder

to the straight guide

. Insert

the guide bar

in the hole on the base. Attach and

tighten the two wing bolts (A) (M6 × 15)

in the

approximate position. Use the feed screw

to make

minute adjustments of the measurements from the bit

to the guide plane

. Tighten the wing bolt (C) (M6 ×

Bottom of Sub base

ABC

16.5 mm 18 mm

18.5 mm 20 mm

4.5 mm

25.5 mm 27 mm

28.5 mm 30 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi m 8 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info