Bedienungsanleitung Hitec AGGRESSOR_CRX (Seite 4 von 8) (Englisch)

30140

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

5 Receiver Servo Connections

4. Recharging Batteries

Alkaline or

rechargable "AA"size

Battery Cover

Battery Case

       

   

7.2V

     

    

        

     



     

       

        

Elecric Car Installation

ESC

RECEIVER

CH1

CH2

Nicad Battery

Battery Holder

Battery Cover

Individual cell Battery Installation Nicad Battery Installation

- Connect the included Hitec CG-25 overnight wall charger to the transmitter

charging jack located under the switch to charge.

- Note: If the charger is properly hooked up to the transmitter, the red light on the charger

will be lit while charging. If the red light does not glow, check the connection or the battery.

- The CG-25 can also charge a 4 cell Nicad receiver battery through the

second output pigtail connected to the switch harness.

- Note: If the charger is properly hooked up to the receiver battery, the green light on the charger

will be lit while charging. If the green light does not glow, check the connection or the battery.

- A full charge on the supplied transmitter Nicad battery pack will take 12-16 hours.

- Warning: Do not attempt to charge alkaline batteries or they may explode.

A) Receiver

- DCX dual conversion.

- You can use a separate receiver 4.8v - 6V battery pack if required for your particular model.

This battery is typically only used with a gas or nitro powered vehicle to supply power to the receiver.

Connect as shown.

- Note: If using an electronic speed control, it will supply the power to the

receiver through the connector plugged into channel #2.

- Be aware you should keep your receiver antenna at least 2" away from

any power wires to prevent potential interference.

- Route the antenna up an antenna tube as typically shown in your vehicles instructions.

- Warning: Be sure not to cut off any excess antenna wire, as it will shorten your operating range.

B) Servos

- The HS-325HB heavy duty gear, ball bearing servo is only include with the standard version systems

part#127271 and #127751. All other sytems come without servos. See the included list for reference.

- Note: Always use the proper servo for your application. Using a servo that is not powerful enough

can damage it and your vehicle could potentially go out of control.

- When installing the servos, refer to the manual of the vehicle for proper installation.

- Once your servos are correctly installed, make sure they are properly centered. To do this,

remove the servo horns, turn on your transmitter, then switch on the power to your receiver.

- Note: Remember; always turn your transmitter on first and off last. Failure to do so may result in

loss of control and damage to your servos and/or linkage.

- Now that the power is on check that the servos are working properly.

- Center the trims and sub-trims, and then replace the horns so that they are centered.

- Be aware they may not be perfectly centered; this is OK, just get them as close as possible,

and then use the trims or sub-trims for fine-tuning.

C) Battery

- The AA receiver battery holder supplied with your radio should be used in a non-electric vehicle

requiring two servos.

- Connect the AA receiver battery holder to the power switch supplied or an optional 4-5 cell Nicad or

NiMh pack to the optional #57215S power switch, and then plug the switch harness into the

"Batt" channel of the receiver for power.(See illustration)

- You will not need this battery if you are using an electric car with an electronic or mechanical

speed control with BEC.

Ok! Now let's get to the programming!

    

             

Gas/Nitro Car Installation

RECEIVER

CH1

CH2

BATT

 

4.8~6.0V

Note: Only one battery should be

connected at a time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitec AGGRESSOR_CRX Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info