580725
5
Zoom out
Zoom in
Vorherige Seite
1/160
Nächste Seite
H) Inserttheemptyinglever(19)inits
positionand putinthelimitstopscrew
(20)with itsnut(21).
3.3 GRASS-CATCHER SUPPORTASSEMBLY
F
itthetwobrackets(1)ontherearplate
(2),usingforeachbracketthreescrews
(3) whicharesupplied, asshown, with-
outfully tighteningthenuts(4).
The supports (1) must be mounted so
that the wings (1a) are turned inwards.
Hook the upper part of the grass-
catcherframe(5)ontothebracketsand
centreitupwiththerearplate(2).
Adjust the position of the two brackets
(1)tothestop(6)sothat,whenturning
thegrass-catcherframe,thepin(7)slots
intothe seat(8)correctly.
Checkagain thatthe frame(5) isprop-
erly centred with the rear plate (2) and
thatitrotatescorrectly,asshownabove,
andthenfullytightenthe screws(3)andthenuts(4).
3.4 ASSEMBLINGTHE LEVERS FORTIPPING
THE GRASS-CATCHER
Positiontheleveraxle(1)inthenotch
ofthetwoplates(2)andattachthem
on the internal side of the grass-
catcher supports (3), using the in-
cluded screws (4) in the sequence
shown.
Connecttheendoftherod(5)ofthe
lifting piston tothe lever (6) withthe
pin(7)andattachthetwosnaprings
(8).
Beforeattachingthegrass-catchertoitssupports,makesurethat
thetipping levermovesproperly.
3.5 REMOVAL OFTHESTOP FROMTHE HOOKINGPAWL
OFTHEGRASS-CATCHER
Fortransport purposes,thepawl(1)hook-
ingthegrass-catcherisheldontotherear
plate by a stop (2).This stop must be re-
moved before fitting the grass-catcher
brackets, and is not to be subsequently
used.
H
F2• •SB
H
F2• •HM
HF2••HT
3.2 GRASS-CATCHER ASSEMBLY
A) Jointheupperpartoftheframe(1)to
thefrontcomponent(2) usingthesupplied
screwsand nuts(3)asshown.Fitthetwo
rubbercaps(4)intothe holesinthetube
offrontframe(2).
B) Before fully tightening the nuts (3),
insert the two supports (5) between the
plates of the upper frame (1) with the
rollersturnedinwards.Fastenthem with
the screws and nuts (6) and then fully
tightenthe nuts(3).
C-D) Attachthetwosideelements(7),usingthescrewsandnuts
(8and 9)asshown.Fit thetworubbercaps (10)intotheholesin
thetwosideelements(7).
E) Inserttheframeinthecanvascover(11)makingsureitiscorrectly
positionedonthebaseperimeter.Hooktheplasticprofiles(12)onto
theframetubeswith theaidofascrew-driver(13).
F) Placetheplate(14)betweenthecan-
vasandthelowerpartoftheframe’sright
sideelement (7a),lininguptheholes.
F) Attach the stiffening bar (15) under the
frame with screws and nuts (16) keeping
theflat partturnedtowardsthecanvas.
G) Using the six screws (18), attach the
cover(17)totheframe’supperpart(1).
HF2••HMHF2• •SB
HF2• •HT
5 EN
C
L
A
K
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

honda-hf2622

Suche zurücksetzen

  • Hallo , ich benötige einen Riemenlaufplan für meinen Honda HF2622 Eingereicht am 31-5-2023 17:10

    Antworten Frage melden
  • Haben ein Problem beim Honda hf 2622,erfährt nicht vorwärts noch rückwärts was ist das für ein Problem. Eingereicht am 5-9-2022 12:37

    Antworten Frage melden
  • Nachdem Mähwerkknopf gezogen wurde läuft das Mähwerk nicht an, Motor läuft Eingereicht am 7-11-2021 11:47

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Honda HF2622 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info