Bedienungsanleitung Honda Honda Engines GCV520 (Seite 3 von 58) (Französisch, Spanisch)

13065

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

BEFORE OPERATION CHECKSFEATURES

IS YOUR ENGINE READY TO GO?

Check the General Condition of the Engine

Fuel-cut Solenoid

Oil Pressure Switch (applicable types):

Check the Equipment Powered by This Engine

Check the Engine

ENGLISH

For your safety, and to maximize the service life of your

equipment, it is very important to take a few moments before you

operate the engine to check its condition. Be sure to take care of

any problem you find, or have your servicing dealer correct it,

before you operate the engine.

Improperly maintaining this engine, or failure to

correct a problem before operation, can cause a

malfunction in which you can be seriously hurt or

killed.

Always perform a pre-operation inspection before

each operation, and correct any problem.

Before beginning your pre-operation checks, be sure the engine is

level and the engine switch is in the OFF position.

Always check the following items before you start the engine:

Look around and underneath the engine for signs of oil or

gasoline leaks.

Remove any excessive dirt or debris, especially around the

muffler and recoil starter.

The engine must be connected to the battery to energize the fuel-

cut solenoid, allowing the engine to run. If the battery is

disconnected, fuel flow to the carburetor main jet will stop.

The engine is equipped with a fuel-cut solenoid that allows fuel to

flow to the carburetor main jet when the engine switch is in the ON

or START position and stops the flow of fuel to the main jet when

the engine switch is in the OFF position.

The engine is equipped with an oil pressure switch to prevent

damage from lack of lubrication or overheating.

If the oil pressure alarm lamp comes on, check the engine oil level

and add the correct engine oil if necessary (see page ).

To restart the engine, turn the engine switch to the OFF position.

Next, start according to the starting procedure.

If the oil pressure alarm lamp continues to light even through the

engine oil level is correct, stop operating the engine and see an

authorized Honda servicing dealers.

Review the instructions provided with the equipment powered

by this engine for any precautions and procedures that should

be followed before engine startup.

Check the air filter element (see page ). A dirty air filter

element will restrict air flow to the carburetor, reducing engine

performance.

Check the engine oil level (see page ). Running the engine

with a low oil level can cause engine damage.

Check the fuel level. Starting with a full tank will help to

eliminate or reduce operating interruptions for refueling.

Check that all shields and covers are in place, and all nuts, bolts,

and screws are tightened.

Look for signs of damage.

Remove any objects or debris that may block the cooling air

intake at the recoil starter/fan cover. Running the engine with a

blocked air intake can cause engine damage.

08/06/18 15:33:23 32Z5Z600_003

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda Honda Engines GCV520 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honda Honda Engines GCV520

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info