Bedienungsanleitung Honeywell 17000 (Seite 4 von 36) (Englisch, Französisch, Spanisch)

723808

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

To Reset Filter Indicator

• Once the filter has been checked and cleaned or replaced as

needed, the filter indicator will need to be reset.

• With the unit powered on, press and hold the appropriate filter

indicator button down for approximately 10 seconds until the light

turns off (Fig. 1).

The Intelli-Check

™

Filter Indicators serve as a convenient guideline for when to clean the

LifeTime HEPA

™

Permanent Filter and when to replace the carbon pre-filter. Depending

upon your individual usage (environment and hours used), you may need to clean/replace

the filters more or less frequently.

When the

HEPA Filter Indicator Light turns on, it’s time to clean your HEPA filter. The

Intelli-Check

™

reminder for when to clean the HEPA filter is intended as a guideline only as

the performance of the filter media is dependent on the concentration of the contaminants

to which the system is exposed. If there are sources of large amounts of contaminant

generation (such as dust from woodworking or heavy smoking) the HEPA filter in your air

purifier may need to be cleaned more often. For instructions on how to clean your HEPA

filter, refer to section “Cleaning the LifeTime HEPA

™

Permanent Filter” in this manual.

When your

Pre-filter Indicator Light turns on, it’

s time to replace your pre-filter. It should

be replaced at least every 3 months. If there are heavy concentrations of odors, smoke, or

large particles in the home, you may need to change the carbon pre-filter more often. For

instructions on how to replace your pre-filter, refer to section “Removing/Changing the

Filters” in this manual.

Note: We do not recommend operating the air purifier without the carbon pre-filter.

Fig 1

• CONNECT THE BATTERY. The programmable controls

and real time clock are battery backed. Upon initial set-up, pull

the protective film from the battery door so the battery will

make contact and function (Fig. 2). This battery allows you to

temporarily unplug your air cleaner without losing program

settings.

• INSTALL PRE-FILTER BEFORE USE. Locate the pre-filter in

the packaging. Refer to the "How to Install and Replace the

Filters" section for proper installation.

• SET CURRENT TIME. Plug unit in outlet.

NOTE: The air cleaner cannot be programmed unless it is plugged into the outlet.

Hold SET button down for approximately 3 seconds. The clock icon and word TIME

will appear. You may adjust the hours using the up button and adjust the minutes

using the down button. After the current time is set, repeatedly press SET button until

( ) disappears.

Fig. 2

Intelli-Check

™

Filter Indicator: Model 17000

Reset Filter Indicator/Turn Light Off: Model 17000

Set-Up: Model 17005

17000-17005 OM EFS.qxd 8/19/05 3:38 PM Page 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell 17000 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info