Bedienungsanleitung Honeywell Dualtech TS100 (Seite 4 von 4) (Englisch)

702753

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

TS100 – assembly directives

TS100 - Installation

If system was previously programmed, remove the telephone handset used for programming

from output “Line Output”.

1. Connect incoming PSTN line to socket ”PSTN Input”

2. Connect alarm transmitter line input to socket ”Line Output”.

3. Connect alarm outputs ”Tamper Output (”E1” ”E1”)” (activated at removal of the cabinet lid), ”E3”

(activated at PSTN Line error.) and ”E2” (activated at any kind of GSM error) to alarm inputs of the alarm

transmitter. NOTE: E2 and E3 are open collector outputs breaking from or closing to GND.

4. Mount the antenna into the GSM transceiver.

5. Insert a GSM SIM card into the unit SIM card reader.

6. TS100 immediately starts up when supply voltage is connected to socket ”Supply Input”. During a start up

period all LED´s will flash, whereafter the LED´s commence idle indication (Green LED flashing and rest of the

LED´s switched off).

7. Locate suitable antenna placement by switching DIP switch number 8 to ”ON” position. This makes the

LED´s indicate the signal strength of the GSM network (similar to an ordinary mobile telephone).

8. Test the system by removing the PSTN Line from socket ”PSTN Input”. Output ”Line Output” immediately

switches to GSM channel and after the delay time stated by the configuration DIP switch, alarm output ”E3” is

activated, an alarm event is triggered on the alarm transmitter connected to the TS90SMS, and the transmitter

dials to report the PSTN error via the GSM channel.

9. If so wanted, an ordinary telephone may be connected to socket ”GSM Output”. Via this socket it´s possible

to make ordinary speech calls vis the GSM network as long as the PSTN line is intact.

NOTE: The TS100 may also be used as single communication channel where no PSTN line is available. In this

case, just ignore the parts concerning the connection of the PSTN line and the TS100 alarm outputs. Also note

that the GSM OUTPUT socket is of no use in this configuration.

Placing the antenna

Locate suitable antenna placement using DIP 8 of the TS90 ”Configuration Switch” (normally, the antenna may

be mounted on top of the TS90 cabinet). Put the antenna cable through the cut out corner of the TS100 cabinet.

Inserting a SIM card

Open the lock on the SIM card holder by pushing it gently in the opposite direction than the one shown by the

arrow located on the holder. Fold back the SIM card holder. Insert the SIM card gently into the holder. The SIM

card circuits should be turned down towards the connectors of the SIM card holder. Fold down the SIM card

holder.Close the lock on the card holder by pushing it in the arrow direction.

Important notes

ü TS100 must be located first on incoming PSTN Line!

ü Make sure the GSM SIM card used is not locked with a PIN code. Use an ordinary cellullar phone to

turn the PIN code protection off

ü If TS100:s alarm outputs (”Tamper Output (E1 E1)”, ”GSM Error (E2)” and ”PSTN Error (E3)”) are

to be used, the alarm transmitter connected to the unit must be programmed with alarm characters

corresponding to these errors.

ü Alarm transmitter must always dial area code before alarm centre telephone number.

TS100 – remote control possibilities

The TS100 output marked “O1 O/C OUT” may be activated/deactivated from remote. To access the remote control

possibilities, a call is made to the TS100 unit, a PIN code is entered at request from the TS100, and desired action is

stated. The TS100 will perform the action desired and return a status SMS message to the phone number

programmed as SMS receiver phone number 3, verifying that the action has been taken.

1. Call the TS100 unit (make a call to the phone number of the SIM card located in the unit) from a tone

dialling telephone handset.

2. When detecting an incoming call, the TS100 will auto-answer and reply with one short beep.

3. Enter remote PIN code (default: 1234) on the calling telephone keypad.

4. TS100 will acknowledge the code with a new short beep. If the wrong code is entered, the TS100 will

immediately hang up the call.

5. After getting an acknowledge of the PIN code, the following remote options are available:

Digit entered on the calling telephone

keypad

Action taken by the TS100

Output O/C OUT is immediately de-

activated (broke from GND)

Output O/C OUT is immediately

activated (closed to GND)

Output O/C OUT is not effected, but a

status SMS message is delivered to SMS

receiver phone number 3

6. Any order will be acknowledge with three short beeps and a status SMS message:

Dualtech IT AB, Time: 12:35:28, Output: ON

will be delivered to SMS receiver phone number 3 (if programmed).

Additional remote feature in TS100 software revision 1.1 (not available in revision 1.0):

After receiving the “PIN code accepted beep”, push 3 for remote PIN code update. TS100 will reply with a new

short beep. Now enter new remote PIN code (4 digits, 0-9). When pushing the fourth digit, the TS100 remote PIN

will immediately be updated. Action is acknowledged with three short beeps.

Antenna connector

SIM Card Reader

Plastic Distances

Cable

throughput

1. Push the plastic distances from behind

through the circuit board mounting holes

of the TS100 cabinet.

2. Snap the TS100 circuit board onto the

plastic distances.

3. Gently push the antenna connector into

the TS100 GSM transceiver.

4. Put the rubber cable throughput into

the cable throughput hole in the TS100

cabinet.

Honeywell Dualtech TS100 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info