Bedienungsanleitung Honeywell HEV620 series (Seite 4 von 29) (Englisch, Französisch, Spanisch)

723828

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

6 7

USING YOUR HUMIDIFIER – HEV620

Power

1. Plug humidiﬁer into a 120V outlet.

CAUTION: To avoid electric shock, DO NOT plug humidiﬁer into outlet with

wet hands.

2. Press Power Button (A).

Humidiﬁer will turn on to high output and high humidity settings. Press again to turn off.

If humidiﬁer was programmed before turning off, previous settings will be remembered.

Unplugging the humidiﬁer resets to default settings.

Moisture Output

3. Press the Moisture Output button (B) to toggle through low, medium, and high

moisture output settings.

A higher setting will provide more moisture output. The fan will pull more moisture off the

Wicking Filter and into the air. The water level in the Water Tank will decrease faster with a

higher setting, since more moisture is going into the air.

A lower setting will provide less moisture output. The fan will run quieter, and the Water Tank

will not have to be ﬁlled as frequently, since less moisture is going into the air.

NOTE: While the humidiﬁer is operating, you will hear the fan running but will not see the

moisture output. This is normal for an evaporative humidiﬁer.

Humidity Control

4. Press the Humidity Control arrows (C) to set the desired humidity level.

To scroll through the numbers faster, press and hold the arrow for 3 seconds.

Release the button once the desired level is shown. Display will blink three times showing

the SET humidity level, then the display will return to show the current room humidity level.

CURRENT will illuminate on the display to indicate the curent room humidity level.

Key

A. Power

B. Moisture Output

C. Humidity Control

D. Timer

E. Check Filter

F. Reﬁll

Symbols

(Canada only)

B. Moisture

Output

D. Timer

E. Check

Filter

F. Reﬁll

HEV620 Digital Display

The humidistat can be set between 30%-69%. Below 30%, LO will illuminate on the display

to indicate the minimum humidity level. Above 69%, the display will show HI to indicate the

maximum humidity level is set.

NOTE: The % number displayed on the control panel represents the relative humidity

(RH) as measured at the Humidistat sensor. The relative humidity in your room may

vary from the number displayed on the humidiﬁer. To measure the RH level in your

room, consider using a Honeywell humidity monitor (HHM10 or H10C) that can be

moved around in the room.

Humidity Reached (US models only)

When the set humidity level is reached HUMIDITY REACHED will appear on the display

and the humidiﬁer will turn off. As long as HUMIDITY REACHED is illuminated, the

fan will not run.

Once the humidity level drops below the set level, HUMIDITY REACHED will disappear

and the humidiﬁer will start running again.

To increase the set humidity level, press the Humidity Control arrows .

Timer

Press the button (D) to set the Timer to 4, 8 or 12 Hours.

NOTE: Humidiﬁer will continue to cycle on and off to maintain the set humidity level while

the Timer is set. At the end of the timed cycle, the humidiﬁer will power off, regardless of the

humidity setting. Any time the humidiﬁer is manually turned off (with the power button or by

unplugging) the timer will reset to OFF setting.

USING YOUR HUMIDIFIER – HEV620 (CONTINUED)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell HEV620 series Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info