Bedienungsanleitung Honeywell HR 80 (Seite 5 von 6) (Deutsch, Englisch)

458015

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

If several radiator controllers are to be controlled simultaneously

in one room:

► Press the binding procedure button on all the radiator

controllers consecutively.

► Activate binding procedure at the command centre (see

operating instructions of the command centre).

During binding procedure, the symbol is shown

continuously in the display of the radiator controller. The

following is displayed:

The radiator controller receives data from the command

centre. This process can take up to 4 minutes.

Failed binding procedure

The binding procedure has failed if the symbol extinguishes.

Take the following measures:

► Remove the disturbing/shielding devices, e.g. wireless

headphones, cordless telephones, loudspeakers, garage door

openers.

► Repeat the binding procedure.

If the symbol extinguishes during normal operation, possible

causes are discharged batteries at the command centre. You do

not have to repeat binding operation, if the communication is

reestablished. If you remove the batteries and insert them again,

the HR80 goes direct in sync mode.

The set temperature at the radiator controller is

automatically set to 20 °C.

FINISHING INSTALLATION OF RADIATOR CONTROLLER

1. Turn the retaining bracket

on the operating unit until

the tip points upwards.

The lock on the coupling

module opens.

2. Slide the operating unit

onto the coupling module.

3. Turn the retaining bracket

to the side.

The operating unit and coupling module are connected

firmly.The

symbol disappears from the display of the

HR 80. The radiator controller is now ready for operation.

To separate operating unit and coupling module proceed in reverse

order.

OPERATION

Every local change in the setpoint temperature remains valid until

a time program overwrites it automatically.

The set temperature is controlled by the command centre and

set there as well. For further information please refer to the

operating instructions of the command centre.

CHANGING SET TEMPERATURE WITH ADJUSTMENT DIAL

► Turn the adjustment dial of the operating unit until the desired

set temperature (between 5 – 30 °C) is displayed.

The range for the set temperature (standard range: 5 – 30 °C) can

be restricted at the command centre.

In order to open or close the radiator valve completely:

► Turn the adjustment dial until "OFF" (closed) or "ON" (opened)

is displayed. (If temperature limits are set, "ON"/"OFF" is not

displayed.)

INSERTING/CHANGING BATTERIES

If Batt appears in the display, both batteries must be replaced.

If the batteries are too weak, the radiator controller opens the

radiator valve completely.

If the batteries are replaced after the binding procedure has been

completed,

is displayed.

The radiator controller waits for data from the command

centre (see section "Activating binding procedure").

1. Open battery

compartment.

2. If necessary, remove

empty batteries.

3. Insert the new batteries

into the battery compart-

ment. Ensure that the

polarity is correct.

4. Close the battery

compartment.

Do not dispose of batteries with household trash. They must be

returned in accordance with the local statutory requirements.

Always replace both batteries.

Only use 1.5 V alkaline batteries of the type LR06.

EMERGENCY OPERATION WITH EMPTY BATTERIES

1. Separate operating unit

from coupling module.

2. Use the adjustment dial to

open (in the direction of the

plus sign) or close (in the

direction of the minus sign)

the heating valve manually.

DEF (DEFAULT SETTING) AND FULL OPERATING MODES

In order to change between the two operating modes, press the

binding procedure button (1, section "Activating binding pro-

cedure") until the respective operating mode is shown on the

display.

Def (default setting) operating mode

The HR 80 operates with the optimum valve lift that is required

for room temperature control.

Full operating mode

If the complete valve lift is to be used or if the valve does not

close completely, you have to set the HR 80 to the full

operating mode.

The battery lifetime is reduced in the full operating mode.

RESETTING THE HR 80 TO THE FACTORY SETTINGS

► Separate operating unit from the valve lantern, see Section

"Finishing installation of radiator controller".

► Remove the batteries.

► Insert the batteries again while keeping the binding procedure

button (see section "Activating binding procedure") pressed.

► Attach the operating unit to the valve lantern.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell HR 80 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honeywell HR 80

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info