Bedienungsanleitung Honeywell Single Zone - Y87RF (Seite 15 von 16) (Englisch)

680980

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

10. Unclip the mounting plate.

Press the top of the

thermostat downwards, pull

it loose and tilt forwards.

9. First remove the dial.

12. Remove the protective tab

between the batteries.

11. Mount directly to the wall.

The plugs and mounting

screws required are supplied.

Plugs

Screws

14. Replace the dial.

13. Attach the thermostat to

the mounting plate.

Step 1

Hook in here

Step 2

Click into place

Binding to the Boiler Relay

The Single Zone Thermostat is supplied ready to install,

binding is only required if the Thermostat and Boiler Relay

are purchased separately.

2. You can now bind the Single

Zone Thermostat. Touch and

hold on the left touch zone for

approximately 10 seconds.

3. The screen for binding the

Boiler Relay is now displayed.

Successful binding Failed binding

1. First, set the Boiler Relay

into binding mode by holding

down the BIND button for

5 seconds, until the red

LED ashes 0.5 seconds

on 0.5 seconds off.

Press here

4. When the symbol ‘bo’ is flashing, briefly touch

the left touch zone to send the binding signal,

at which point the

symbol will flash several times.

5. If binding has been successful the number indicates

the signal strength (1 = min to 5 = max).

If binding fails, appears on screen. Please try again.

6. The red LED on the Boiler Relay will turn off when binding

has been successful.

Note: binding can be cancelled from the binding

screen by touching and holding on the left touch

zone for approximately 10 seconds.

Installation Menu

The single Zone Thermostat has an Installation

Menu that is used to set the minimum and maximum

temperature limits and the off temperature setting.

Maximum and minimum temperatures:

The maximum temperature you can set your

thermostat to is 35ºC and the minimum is 5ºC.

The off temperature:

If the thermostat is operated remotely, this is the temperature

value that is used when it is switched off from the remote app.

4. Touch the left touch zone to

display the off temperature

setting. Change this using

the setting ring as before.

5. The Installation Menu closes

automatically 10 seconds

after the last action.

2. The maximum temperature

limit is now displayed. The

setting can be changed using

the setting ring. There is no

need to confirm the value.

Touch zones.

There are two touch zones just below the thermostat

display, which are used to access menus and functions.

3. While this setting is flashing,

touch the left touch zone

briefly to display the minimum

temperature limit. This can also

be changed using the setting ring.

1. Rotate the setting ring fully to

the left until the minimum value

is shown. When the value starts

flashing, touch and hold on both

left and right touch zones for

approximately 10 seconds.

Activate the Installation Menu as follows:

10s

10s 10s

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell Single Zone - Y87RF Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honeywell Single Zone - Y87RF

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info