652395
25
Zoom out
Zoom in
Vorherige Seite
1/34
Nächste Seite
25
If the alert is disabled, “OFF” will be displayed; otherwise the alert value is shown.
When a wind alert is displayed, press UP or DOWN arrow button to activate or deactivate it.
Wind Alert programming
With the wind icon flashing, press ALARM/CHART button to select the desired alarm.
Press and hold ALARM/CHART button until alert and corresponding icon will flash.
Set the alert using UP or DOWN arrow button. Press and hold either button for fast digits advance.
Press ALARM/CHART button to confirm your selection and return to the wind alert selection screen.
Disabling the Wind Alert
To disable wind alert when it is displayed after pressing ALARM/CHART button press UP or DOWN arrow button – OFF will
be displayed instead of previously set alarm time.
LED Backlight Options
The main unit backlight can be turned on, off or automatic depending on light conditions. The sensitivity of the backlight sensor
can be adjusted to high or low using the switch, located on the back panel.
Note: For continuous backlight control the AC/DC adaptor must be plugged in.
Time Alarm Settings
There are two time alarms available on the main unit: Weekday alarm (W), and Single alarm (S)
If Weekday alarm is activated, it will sound at the set time and the alarm icon will flash Monday through Friday.
If Single day alarm is activated, it will sound at the set time and the alarm icon will flash only for this specific day and
will not activate on subsequent days.
Note: The snooze duration for listed alarms can also be programmed up to 15 minutes.
Enable/Disable Time Alarms
Press the ALARM/CHART button to display the Weekday Alarm or Single Day Alarm time. If these alarms are not set,
the abbreviation OFF will be displayed.
To enable or disable any of these alarms, press UP or DOWN arrow button
Press ALARM/CHART button to confirm your setting
Note: Press SET button anytime during alarm programming mode to return to the default clock display.
Programming Time Alarms
With the Clock and Alarm icon flashing, press the ALARM/CHART button to select the desired alarm.
Press and hold ALARM/CHART button until the hour digit will flash
Set the alarm hour using UP or DOWN arrow button. Press and hold either button for quick digit advance.
Press ALARM/CHART to confirm selection.
Downloaded from www.Manualslib.com manuals search engine
25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Honeywell TE831W-2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info