613689
28
Zoom out
Zoom in
Vorherige Seite
1/34
Nächste Seite
28
Troubleshooting Guide
This is a quick guide to help you diagnose and cope with possible problems with
your wireless control system. For further assistance, please contact your Installer.
Symptom Possible Cause Remedy
ST9520C has a blank LCD
display
No power to the
heating system.
Check that there is power to the
heating system.
Fault in ST9520C Call Installer
ST9520C indicates that
Heating Zones are ON, but
radiators are cold
Temperature controls
are switched off or
set too low.
Check that the temperature
controls in the system are set to
appropriate levels.
Boiler or other
system controls
have malfunctioned.
Call Installer
ST9520C shows the
message:
‘INTERNAL FAULT’
Fault in ST9520C Call Installer
Every few seconds, the
ST9520C screen shows the
message:
ST9520C is
counting down the
number of days
until your next boiler
service is due.
Arrange a boiler service before
the counter reaches zero.
After servicing your boiler, the
Service Engineer / Installer will
reset the ST9520C to remind
you when the next boiler service
is due. Each service is normally
a maximum of 1 year apart.
Although the heating is still
operating, the ST9520C
screen keeps flashing the
message:
Your boiler service
is overdue.
Arrange an immediate boiler
service.
After servicing your boiler, the
Service Engineer / Installer will
reset the ST9520C to remind
you when the next boiler service
is due. Each service is normally
a maximum of 1 year apart.
Can I override the Programmer from the DT92E thermostat?
As well as changing the set temperature from the DT92E, it is also possible to override
the heating system on or off from the DT92E. This is only possible if the ST9520C
is in AUTO or ONCE Modes. If ST9520C is in CONT mode it will not be possible to
switch the heating off from the DT92E. Similarly, if ST9520C is in OFF mode, it will
not be possible to switch the heating on from the DT92E. If these latter overrides are
required it is first necessary to change the ST9520C mode setting to AUTO or ONCE.
FAQ AND TROUBLESHOOTING
28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Honeywell Y9520Z Sundial RF2 Pack 5 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info