Bedienungsanleitung Honeywell YZ667A1060 (Seite 11 von 12) (Englisch)

613662

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

9.2 Manual adaption

Manual adaption can be used to solve various problems:

• if automatic adaption does not work.

• if the entire valve lift is to be utilized.

• if the radiator hardly gets warm at all.

• if the radiator does not become cold.

• if the

symbol is displayed (no adaption possible).

• if the

symbol is displayed (valve lift too short or motor

cannot be moved).

Section 9: Trouble Shooting (cont.)

9.1 Trouble Shooting Guide (cont.)

Symptom (Fault Message)

CM67z display works but heat-

ing does not switch on:

• The HC60NG LEDs are OFF

• The HC60NG green LED is ON

HC60NG red LED is constantly

ON or ﬂashing.

The HR80UK display is blank

or shows bAtt.

The ( ) symbol on the HR80UK

is not displayed.

Possible Cause

No power to HC60NG.

Bad electrical connection to the

boiler or faulty boiler.

RF communication lost due to bad

location of the CM67z room unit.

RF communication fault.

HR80UK batteries exhausted.

RF communication lost due to bad

location of the CM67z room unit.

RF communication fault.

Remedy

Check the power to the HC60NG is on.

Check the boiler and HC60NG power supply as well as electrical

connection between the boiler and HC60NG.

Hook the room unit back on the wall bracket or return the room unit

on the table stand to the position where communication was reliable.

Call the Honeywell Technical Help-Desk, details on the back page.

NOTE: The boiler can be controlled manually when RF communication

is lost. Press the HC60NG push button to switch the boiler on or off.

When the green LED is on - the boiler is on.

Replace the HR80UK batteries following the guidelines in the

HR80UK user instruction.

Hook the room unit back on the wall bracket or return the room

unit on the table stand to the position where communication was

reliable.

Call the Honeywell Technical Help-Desk, details on the back page.

During Normal Operation

9.4 Resetting the HR 80 to the factory settings

•

Separate operating unit from the coupling module (Fig.

• Remove the batteries.

•

Insert the batteries again while keeping the binding

procedure button pressed.

•

Attach the operating unit to the

coupling module (Fig.

)

9.3 Def (default setting) and Full operating modes

In order to change between the two

operating modes, press the ‘binding

button’ until the respective operating

mode is shown on the display.

Def (default setting) operating mode

The HR 80 operates with the optimum valve lift that is required

for room temperature control.

Full operating mode

If the complete valve lift is to be used or if the valve does

not close completely, you have to set the HR 80 to the full

operating mode.

The battery lifetime is reduced in the full operating

mode.

Binding

Button

Turn the locking knob

and seperate the operating unit and

coupling module.

Attach the operating unit to the

coupling module and turn the

locking knob

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell YZ667A1060 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info