Zoom out
Zoom in
Vorherige Seite
1/11
Nächste Seite
Aruba 300 Series Wireless Access Point
Installation Guide
Rev03 | August 2018 1
The Aruba 300 Series wireless access points (APs) support IEEE802.11ac standards for high-performance WLAN, and are
equipped with two radios, which provide network access and monitor the network simultaneously. These access points deliver
high-performance 802.11n 2.4 GHz and 802.11ac 5 GHz functionality, while also supporting 802.11a/b/g wireless services.
Multi-user Multiple-in, Multiple-output (MU-MIMO) is enabled when operating in 5GHz mode for optimal performance.
The AP-304 and AP-305 access points work in conjunction with an Aruba controller, while the IAP-304 and IAP-305 access point
can be configured using a built-in virtual controller.
The 300 Series wireless access points provide the following capabilities:
IEEE 802.11a/b/g/n/ac operation as a wireless access point
IEEE 802.11a/b/g/n/ac operation as a wireless air monitor
IEEE 802.11a/b/g/n/ac spectrum monitor
Compatible with IEEE 802.3at PoE+ and IEEE 802.3af PoE
Centralized management configuration and upgrade
Integrated Bluetooth Low Energy (BLE) Radio
Package Contents
(I)AP-304 or (I)AP-305 access point
Ceiling Rail Adapter (spare: AP-220-MNT-C1)
Startup Guide
Software
The AP-304 and AP-305 access points require ArubaOS 6.5.1.0 or higher. For additional information, refer to the ArubaOS User
Guide and ArubaOS Quick Start Guide.
The IAP-304 and IAP-305 access points require Aruba Instant 4.3.1.0 or higher. For additional information, refer to the Aruba
Instant User Guide and Aruba Instant Quick Start Guide.
This device must be professionally installed and serviced by a trained ACMP or similar Aruba-certified technician. Aruba
access points are classified as radio transmission devices, and are subject to government regulations of the host country.
The network administrator(s) is/are responsible for ensuring that configuration and operation of this equipment is in
compliance with their country’s regulations. For complete list of approved channels in your country of the AP-304 and AP-305
access points, refer to the Aruba Downloadable Regulatory Table at support.arubanetworks.com.
Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original
packing materials. Use these materials to repack and return the unit to the supplier if needed.
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Inhalt der Seiten


  • Page 1

    Aruba 300 Series Wireless Access Point
    Installation Guide

    The Aruba 300 Series wireless access points (APs) support IEEE802.11ac standards for high-performance WLAN, and are
    equipped with two radios, which provide network access and monitor the network simultaneously. These access points deliver
    high-performance 802.11n 2.4 GHz and 802.11ac 5 GHz functionality, while also supporting 802.11a/b/g wireless services.
    Multi-user Multiple-in, Multiple-output (MU-MIMO) is enabled when operating in 5GHz mode for optimal performance.
    The AP-304 and AP-305 access points work in conjunction with an Aruba controller, while the IAP-304 and IAP-305 access point
    can be configured using a built-in virtual controller.
    The 300 Series wireless access points provide the following capabilities:


    IEEE 802.11a/b/g/n/ac operation as a wireless access point



    IEEE 802.11a/b/g/n/ac operation as a wireless air monitor



    IEEE 802.11a/b/g/n/ac spectrum monitor



    Compatible with IEEE 802.3at PoE+ and IEEE 802.3af PoE



    Centralized management configuration and upgrade



    Integrated Bluetooth Low Energy (BLE) Radio

    This device must be professionally installed and serviced by a trained ACMP or similar Aruba-certified technician. Aruba
    access points are classified as radio transmission devices, and are subject to government regulations of the host country.
    The network administrator(s) is/are responsible for ensuring that configuration and operation of this equipment is in
    compliance with their country’s regulations. For complete list of approved channels in your country of the AP-304 and AP-305
    access points, refer to the Aruba Downloadable Regulatory Table at support.arubanetworks.com.

    Package Contents


    (I)AP-304 or (I)AP-305 access point



    Ceiling Rail Adapter (spare: AP-220-MNT-C1)



    Startup Guide

    Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original
    packing materials. Use these materials to repack and return the unit to the supplier if needed.

    Software
    The AP-304 and AP-305 access points require ArubaOS 6.5.1.0 or higher. For additional information, refer to the ArubaOS User
    Guide and ArubaOS Quick Start Guide.
    The IAP-304 and IAP-305 access points require Aruba Instant 4.3.1.0 or higher. For additional information, refer to the Aruba
    Instant User Guide and Aruba Instant Quick Start Guide.

    Rev03 | August 2018

    1



  • Page 2

    300 Series Hardware Overview
    Figure 1 Status LEDs on AP Front (305 shown)

    System

    Radio

    LEDs
    The 300 Series access points have two LEDs that indicate the system and radio status of the device. These two LEDs can be
    configured via ArubaOS (for AP-304 and AP-305) or Aruba Instant (for IAP-304 and IAP-305) software into three separate
    modes:


    Normal mode (by default): See Table 1



    Both LEDs off



    Blink mode: Both LEDs blink green (synchronized)

    Table 1 300 Series LEDs Status in Normal Mode
    LED

    Color/State

    Meaning

    System Status
    (Left)

    Off

    Device powered off

    Green- Blinking

    Device booting, not ready for use

    Green- Solid

    Device ready for use, no restrictions

    Green- Flashing

    Device ready for use, uplink negotiated in sub optimal speed
    (<1Gbps)

    Amber- Solid

    Device ready for use; power-save mode (802.3af PoE)

    Amber- Flashing

    Device ready for use; power-save mode (802.3af PoE), uplink
    negotiated in sub optimal speed (<1Gbps)

    Red- Solid

    System error condition

    Off

    Device powered off, or both radios disabled

    Green- Solid

    Both radios enabled in access mode

    Green- Blinking

    One radio enabled in access mode

    Amber- Solid

    Both radios enabled in monitor mode

    Amber- Blinking

    One radio enabled in monitor mode

    Alternating

    One radio enabled in access mode, other in monitor mode

    Radio Status
    (Right)

    External Antenna Connectors
    The AP-304 and IAP-304 access points are equipped with three external antenna connectors on the front corners of the access
    point.

    2

    Aruba 300 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide



  • Page 3

    Figure 2 External Antenna Connector

    ANT0

    ANT1

    ANT2
    External antennas for this device must be installed by an Aruba Certified Mobility Professional (ACMP) or other
    Aruba-certified technician, using manufacturer-approved antennas only.
    The Equivalent Isotropically Radiated Power (EIRP) levels for all external antenna devices must not exceed the regulatory
    limit set by the host country/domain.
    Installers are required to record the antenna gain for this device in the system management software.

    USB Interface
    The 300 Series is equipped with a USB port for connectivity with cellular modems and other USB client devices. When powered
    by an 802.3at or DC power source, the USB port can supply power up to 5W/1A. The USB interface is disabled when the access
    point is powered by an 802.3af PoE source (power-save mode).

    Console Port
    The serial console port is located at the back of the device and is a 4-pin connector covered by a dust cover. An optional serial
    adapter cable (AP-CBL-SER) is sold separately to connect the device to a serial terminal or a laptop for direct local
    management.

    Ethernet Port
    The 300 Series access points are equipped with one 10/100/1000Base-T auto-sensing MDI/MDX Ethernet port. This port
    supports wired-network connectivity, in addition to Power over Ethernet (PoE) from IEEE 802.3af and 802.3at compliant power
    sources.
    This device accepts 56V DC (802.3at), or 48V DC (802.3af) nominal as a standard powered device (PD) from power sourcing
    equipment, including PoE midspan injector or a PoE-sourcing network infrastructure.

    Figure 3 Back Panel
    USB Port

    Kensington Lock

    Console Port

    CONSOLE

    DC Power Socket
    12V

    1A

    Reset Button
    Ethernet Port

    Kensington Lock Slot
    The 300 Series access points are equipped with a Kensington lock slot for additional security.
    Aruba 300 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide

    3



  • Page 4

    Reset Button
    To reset the 300 Series access points to factory default settings, press and hold down the reset button using a small, narrow
    object such as a paper clip while the (I)AP is powered on.

    DC Power Socket
    If PoE is not available, an optional Aruba AP-AC-12V30B power adapter kit (sold separately) can be used to power the 300
    Series access points.
    Additionally, a locally-sourced AC-to-DC adapter (or any DC source) can be used to power this device, as long as it complies
    with all applicable local regulatory requirements and the DC interface meets the following specifications:


    12 Vdc (+/- 5%) and at least 18W



    Center-positive 2.1/5.5 mm circular plug, 9.5 mm length

    Before You Begin
    FCC Statement: Improper termination of access points installed in the United States configured to non-US model controllers
    will be in violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a
    requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80).
    EU Statement:
    Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide/Aruba Instant
    User Guide for details on restrictions.
    Produit réseau local radio basse puissance operant dans la bande fréquence 2.4 GHz et 5 GHz. Merci de vous referrer au
    ArubaOS User Guide/Aruba Instant User Guide pour les details des restrictions.
    Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere Informationen bezlüglich
    Einschränkungen finden Sie im ArubaOS User Guide/Aruba Instant User Guide.
    Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento alla ArubaOS User Guide/Aruba Instant User
    Guide per avere informazioni detagliate sulle restrizioni.

    Pre-Installation Network Requirements
    The instructions for this section are applicable to the AP-304 and AP-305 only.
    After WLAN planning is complete and the appropriate products and their placement have been determined, the Aruba
    controller(s) must be installed and initial setup performed before the Aruba access points are deployed.
    For initial setup of the controller, refer to the ArubaOS Quick Start Guide for the software version installed on your controller.

    Pre-Installation Checklist
    Before installing your 300 Series access points, ensure that you have the following:


    Cat5E or better UTP cable of required length



    One of the following power sources:


    IEEE 802.3af-compliant Power over Ethernet (PoE) source.



    Aruba AP-AC-12V30B power adapter kit (sold separately)

    For AP-304 and AP-305 only:


    Aruba Controller provisioned on the network:




    4

    Layer 2/3 network connectivity to your access point

    One of the following network services:


    Aruba Discovery Protocol (ADP)



    DNS server with an “A” record

    Aruba 300 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide



  • Page 5



    DHCP Server with vendor-specific options

    Aruba Networks, Inc., in compliance with governmental requirements, has designed the 300 Series access points so that only
    authorized network administrators can change the settings. For more information about access point configuration, refer to
    the ArubaOS Quick Start Guide /Aruba Instant Quick Start Guide and ArubaOS User Guide/Aruba Instant User Guide.

    Verifying Pre-Installation Connectivity
    The instructions for this section are applicable to the AP-304 and AP-305 only.
    Before installing access points in a network environment, make sure that they are able to locate and connect to the controller
    after power on.
    Specifically, you must verify the following conditions:


    When connected to the network, each access point is assigned a valid IP address



    Access points are able to locate the controller

    Refer to the ArubaOS Quick Start Guide for instructions on locating and connecting to the controller.

    Identifying Specific Installation Locations
    You can mount the 300 Series access point on the ceiling or a wall. Use the access point placement map generated by Aruba’s
    RF Plan software application to determine the proper installation location(s). Each location should be as close as possible to
    the center of the intended coverage area and should be free from obstructions or obvious sources of interference. These RF
    absorbers/reflectors/interference sources will impact RF propagation and should have been accounted for during the planning
    phase and adjusted for in RF plan.

    Identifying Known RF Absorbers, Reflectors and Interference Sources
    Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation phase is critical.
    Make sure that these sources are taken into consideration when you attach an access point to its fixed location. Examples of
    sources that degrade RF performance include:


    Cement and brick



    Objects that contain water



    Metal



    Microwave ovens



    Wireless phones and headsets

    Installing the Access Point
    Service to all Aruba Networks products should be performed by an AMCP certified technician or similar.
    The 300 Series access points ship with a ceiling rail adapter to attach to a 9/16” or 15/16” ceiling rail. Additional ceiling or wall
    mount kits are sold separately as accessories.
    The installer is responsible for securing the access point onto the ceiling tile rail in accordance with the steps below. Failure
    to properly install this product may result in physical injury and/or damage to property.
    1. Pull the necessary cables through a prepared hole in the ceiling tile near where the access point will be placed.
    2. Place the adapter against the back of the access point with the adapter at an angle of approximately 30 degrees to the tabs
    (see Figure 4).
    3. Twist the adapter clockwise until it snaps into place in the tabs (see Figure 4).

    Aruba 300 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide

    5



  • Page 6

    Figure 4 Attaching the Ceiling Rail Adapter to the AP

    4. Hold the access point next to the ceiling tile rail with the mounting slots at approximately a 30-degree angle to the ceiling
    tile rail (see Figure 5 and Figure 6). Make sure that any cable slack is above the ceiling tile.
    5. Pushing toward the ceiling tile, rotate the access point clockwise until the device clicks into place on the ceiling tile rail.

    Figure 5 Mounting the Access Point to a 15/16” ceiling rail

    Figure 6 Mounting the Access Point to a 9/16” ceiling rail

    Connecting Required Cables
    Install cables in accordance with all applicable local and national regulations and practices.

    Verifying Post-Installation Connectivity
    The integrated LEDs on the access point can be used to verify that the access point is receiving power and initializing
    successfully (see Table 1). Refer to the ArubaOS Quick Start Guide/Aruba Instant Quick Start Guide for further details on verifying
    post-installation network connectivity.

    6

    Aruba 300 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide



  • Page 7

    Configuring the 300 Series Access Points
    The instructions for this section are applicable to the AP-304 and AP-305 only.

    Access Point Provisioning/Reprovisioning
    Provisioning parameters are unique to each access point. These local access point parameters are initially configured on the
    controller which are then pushed out to the access point and stored on the access point itself. Aruba recommends that
    provisioning settings be configured via the ArubaOS Web UI only. Refer to the ArubaOS User Guide for complete details.

    Access Point Configuration
    Configuration parameters are network or controller specific and are configured and stored on the controller. Network
    configuration settings are pushed out to the access point but remain stored on the controller.
    Configuration settings can be configured via the ArubaOS Web UI or ArubaOS CLI. Refer to the ArubaOS User Guide for
    complete details.

    Electrical and Environmental Specifications
    For additional specifications on this product, please refer to the product data sheet at www.arubanetworks.com/
    safety_addendum.
    All Aruba access points should be professionally installed by an Aruba Certified Mobility Professional (ACMP). The installer is
    responsible for ensuring that grounding is available and meets applicable national and electrical codes.
    Tous les points d'accès Aruba doivent impérativement être installés par un professionnel agréé. Ce dernier doit s'assurer
    que l'appareil est mis à la terre et que le circuit de mise à la terre est conforme aux codes électriques nationaux en vigueur.

    Electrical




    Ethernet:


    One 100/1000 Base-T auto-sensing Ethernet RJ45 interface



    Power over Ethernet IEEE 802.3at 56VDC (nominal) and 802.3af 48VDC (nominal).

    Power:


    Maximum (worst-case) power consumption: 13.5W (802.3af PoE) or 12W (DC)


    Excludes power consumed by external USB device (and internal overhead); this could add up
    to 6W (PoE) or 5.5W (DC) for 5W/1A USB device



    Direct DC source: 12Vdc nominal, +/- 5%



    Power over Ethernet (PoE): 802.3at and 802.3af complaint source



    Connect only to IEC 60950-1 or IEC 60601-1 3rd edition products and power sources.

    If a power adapter other than the Aruba-approved adapter is used in the US or Canada, it should be NRTL listed, with an
    output rated 12Vdc, minimum 2A, marked “LPS” and “Class 2”, and suitable for plugging into a standard power receptacle in
    the US and Canada.

    Environmental




    Operating:


    Temperature: 0°C to +50°C (+32°F to +122°F)



    Humidity: 5% to 93% non-condensing

    Storage and transport:


    Temperature: -40°C to +70°C (-40°F to +158°F)

    Regulatory Information
    The following regulatory model names apply to the 300 Series access points:

    Aruba 300 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide

    7



  • Page 8



    AP-304/IAP-304: APIN0304



    AP-305/IAP-305: APIN0305

    Aruba Networks provides a multi-language document that contains country-specific restrictions and additional safety and
    regulatory information for all Aruba access points. This document can be viewed or downloaded at www.arubanetworks.com.

    FCC
    This device is electronically labeled.
    To view the FCC ID for controller-managed access points:
    1. Log into the controller WebUI
    2. Navigate to Maintenance > Controller > About
    To view the FCC ID for Instant access points:
    1. Log into the virtual controller WebUI
    2. Navigate to Maintenance > About
    RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should
    be installed and operated with a minimum distance of 7.87 inches (20cm) between the radiator and your body for 2.4 GHz
    and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or
    transmitter.
    Déclaration sur les limites d'exposition aux radiofréquences : cet équipement est conforme aux limites d'exposition aux
    rayonnements radioélectriques spécifiées par la FCC. Il doit être installé et utilisé à une distance minimale de 20 cm par
    rapport à votre corps pour les fréquences de 2,4 et 5 GHz. Cet émetteur-récepteur ne doit pas être utilisé ou situé à
    proximité d'autres antennes ou émetteurs-récepteurs.

    The device could automatically discontinue transmission in case of absence of information to transmit, or operational
    failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive
    codes where required by the technology.

    FCC Class B Part 15
    This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
    the FCC Rules. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
    accordance with the manufacturer’s instructions, may cause interference harmful to radio communications.
    Operation is subject to the following conditions:


    This device may not cause harmful interference.



    This device must accept any interference received, including interference that may cause undesired operation.

    If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is
    encouraged to try to correct the interference by one or more of the following measures:


    Reorient or relocate the receiving antenna.



    Increase the separation between the equipment and receiver.



    Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.



    Consult the dealer or an experienced radio or TV technician for help.

    Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s
    authority to operate this equipment.
    Toute modification effectuée sur cet équipement sans l'autorisation expresse de la partie responsable de la conformité est
    susceptible d'annuler son droit d'utilisation.

    Canada
    Complies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard entitled
    “Digital Apparatus,” CAN ICES-3(B)/NMB-3(B).
    Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or
    lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the
    antenna type and its gain should be so chosen that the equivalent isotropically radiated power (E.I.R.P.) does not exceed the
    limit necessary for successful communication.

    8

    Aruba 300 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide



  • Page 9

    This device complies with Industry Canada license-exempt RSS standard(s).
    Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept
    any interference, including interference that may cause undesired operation of the device.

    Déclaration d’Industrie Canada
    Cet appareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada.
    Conformément aux réglementations d’Industrie Canada, cet émetteur-récepteur radio doit être utilisé uniquement avec une
    antenne dont le type et le gain maximal doivent être approuvés par Industrie Canada. Pour réduire les interférences radio
    potentielles, le type d’antenne et son gain doivent être choisis de façon à ce que la puissance isotrope rayonnée équivalente
    (PIRE) ne dépasse pas les valeurs nécessaires à une communication efficace.
    Ce périphérique est conforme aux règlements RSS exempts de licence d’Industrie Canada. L’utilisation de ce périphérique est
    soumise aux deux conditions suivantes : (1) ce périphérique ne doit pas provoquer d’interférences, et (2) ce périphérique doit
    accepter toute interférence, y compris les interférences susceptibles de provoquer un dysfonctionnement.

    This equipment complies with IC RSS-102 RF exposure limits set forth for an uncontrolled environment. This
    equipment should be installed and operated with minimum distance 20 cm between the radiator and your
    body.
    Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement
    non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la
    source de rayonnement et votre corps.

    Under Industry Canada regulations, when operated in 5150 to 5250 MHz frequency range, this device is
    restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite
    Systems. Users are advised that high power radars are allocated as primary users (i.e. priority users) of the
    bands 5250-5350 MHz and 5650-5850MHz and that these radars could cause interference and/or damage to
    LE-LAN devices.
    Conformément aux réglementations d’Industrie Canada, en cas d'utilisation dans la plage de fréquences de
    5150 à 5250 MHz, cet appareil doit uniquement être utilisé en intérieur afin de réduire les risques
    d'interférence avec les systèmes satellites mobiles partageant le même canal. Les utilisateurs êtes avisés que
    les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité)
    pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des
    dommages aux dispositifs LAN-EL

    EU Regulatory Conformance
    Aruba Networks Inc., hereby declares that this product is in compliance with the directives listed below:


    EMC Directive 2014



    Low Voltage Directive 2014



    R&TTE Directive 1999



    REACH Regulation (EC) No.: 1907/2006



    RoHS Directive 2011



    WEEE Directive 2012

    A Declaration of Conformity for these directives is available for viewing at www.arubanetworks.com.

    EMC Class B Warning
    이 기기는 가정용 (B 급 ) 전자파적합기기로서 주로 가정에서 사용하는 것을 목적으로 하며 , 모든 지역에서 사용할 수
    있습니다 .

    RF Warning
    해당무선설비는 전파혼신의 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다

    Medical
    1. Equipment not suitable for use in the presence of flammable mixtures.

    Aruba 300 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide

    9



  • Page 10

    2. Connect to only IEC 60950-1 or IEC 60601-1 3rd edition certified products and power sources. The end user is responsible
    for the resulting medical system complies with the requirements of IEC 60601-1 3rd edition.
    3. Wipe with a dry cloth, no additional maintenance required.
    4. No serviceable parts, the unit must be sent back to the manufacturer for repair.
    5. No modifications are allowed without Aruba approval.

    Taiwan
    第十二條 → 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 
    第十四條 → 低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。 
    前項合法通信,指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

    Expected Service Life 10 years. For additional compliance information, refer to the regulatory label on the back of this device.

    Proper Disposal of Aruba Equipment
    Dispose of Aruba products per local regulation. For the most current information about Global Environmental Compliance and
    Aruba products, visit www.arubanetworks.com.

    Waste of Electrical and Electronic Equipment
    Aruba products at end of life are subject to separate collection and treatment in the EU Member States,
    Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie
    bin). The treatment applied at end of life of these products in these countries shall comply with the
    applicable national laws of countries implementing Directive 2002/96/EC on Waste of Electrical and
    Electronic Equipment (WEEE).

    India RoHS
    This product complies with RoHS requirements as prescribed by E-Waste (Management & Handling) Rules, governed by the
    Ministry of Environment & Forests, Government of India.

    European Union RoHS
    Aruba products also comply with the EU Restriction of Hazardous Substances Directive 2011/65/EC
    (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and
    electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including
    Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine.
    Some Aruba products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit
    assemblies). Products and packaging will be marked with the “RoHS” label shown at the left indicating conformance to this
    directive.

    China RoHS
    Aruba products also comply with China environmental declaration requirements and are labeled with the
    “EFUP 25” label shown at the left.

    25
    ᴹ∂ᴹᇣ⢙䍘༠᰾
    Hazardous Materials Declaration
    ᴹ∂ᴹᇣ⢙䍘ᡆ‫ݳ‬㍐˄Hazardous Substance˅
    䜘Ԧ਽〠
    (Parts)
    ⭥䐟⁑ඇ
    (circuit modules)
    ⭥㔶৺⭥㔶㓴Ԧ
    (Cables & Cable Assemblies)
    䠁኎䜘Ԧ
    (Metal Parts)
    ກᯉ઼㚊ਸ⢙䜘Ԧ
    (Plastic and Polymeric Parts)







    ‫ޝ‬ԧ䬜

    ཊⓤ㚄㤟

    ཊⓤҼ㤟䟊

    ˄Pb˅

    ˄Hg˅

    ˄Cd˅

    ˄Cr6+˅

    ˄PBB˅

    ˄PBDE˅

    X

    O

    O

    O

    O

    O

    O

    O

    O

    O

    O

    O

    O

    O

    O

    O

    O

    O

    O

    O

    O

    O

    O

    O

    O: 㺘⽪䈕ᴹ∂ᴹᇣ⢙䍘൘䈕䜘Ԧᡰᴹ൷䍘ᶀᯉѝⲴਜ਼䟿൷൘ SJ/T11363-2006 ḷ߶㿴ᇊⲴ䲀䟿㾱≲
    ԕлDŽIndicates that the concentration of the hazardous substance in all homogeneous materials in the parts
    is below the relevant threshold of the SJ/T11363-2006 standard.
    X: 㺘⽪䈕ᴹ∂ᴹᇣ⢙䍘㠣ቁ൘䈕䜘ԦⲴḀа൷䍘ᶀᯉѝⲴਜ਼䟿䎵ࠪ SJ/T11363-2006 ḷ߶㿴ᇊⲴ䲀
    䟿㾱≲DŽIndicates that the concentration of the hazardous substance of at least one of all homogeneous
    materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard.
    ሩ䬰୞ѻᰕⲴᡰ୞ӗ૱ˈᵜ㺘ᱮ⽪‫׋‬ᓄ䬮Ⲵ⭥ᆀؑ᚟ӗ૱ਟ㜭वਜ਼䘉Ӌ⢙䍘DŽ
    This table shows where these substances may be found in the supply chain of electronic information products, as
    of the date of sale of the enclosed product.
    ↔ḷᘇѪ䪸ሩᡰ⎹৺ӗ૱Ⲵ⧟‫⭘֯؍‬ᵏḷᘇ. ḀӋ䴦䜘ԦՊᴹањн਼Ⲵ⧟‫⭘֯؍‬ᵏ
    (ֻྲ,⭥⊐অ‫⁑ݳ‬ඇ)䍤൘ަӗ૱к.
    ↔⧟‫⭘֯؍‬ᵏ䲀ਚ䘲⭘Ҿӗ૱ᱟ൘ӗ૱᡻޼ѝᡰ㿴ᇊⲴᶑԦлᐕ֌.
    The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are
    per the symbol shown here. The Environment- Friendly Use Period is valid only when the
    product is operated under the conditions defined in the product manual.

    10

    25

    Aruba 300 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide



  • Page 11

    Contacting Support
    Table 2 Contact Information
    Main Site

    www.arubanetworks.com

    Support Site

    https://support.arubanetworks.com

    Airheads Social Forums and Knowledge
    Base

    community.arubanetworks.com

    North American Telephone

    1-800-943-4526 (Toll Free)
    1-408-754-1200

    International Telephones

    http://www.arubanetworks.com/support-services/contact-support/

    Software Licensing Site

    https://hpe.com/networking/support

    End of Support information

    http://www.arubanetworks.com/support-services/end-of-lifeproducts/end-of-life-policy/

    Security Incident Response Team (SIRT)

    Site: http://www.arubanetworks.com/support-services/securitybulletins/
    Email: sirt@arubanetworks.com

    Copyright
    © Copyright 2018 Hewlett Packard Enterprise Development LP

    Open Source Code
    This product includes code licensed under the GNU General Public License, the GNU Lesser General Public
    License, and/or certain other open source licenses. A complete machine-readable copy of the source code
    corresponding to such code is available upon request. This offer is valid to anyone in receipt of this information
    and shall expire three years following the date of the final distribution of this product version by Hewlett Packard
    Enterprise Company. To obtain such source code, send a check or money order in the amount of US $10.00 to:
    Hewlett Packard Enterprise Company
    Attn: General Counsel
    3000 Hanover Street
    Palo Alto, CA 94304
    USA

    Warranty
    This hardware product is protected by an Aruba warranty. For more details visit www.hpe.com/us/en/
    support.html

    Aruba 300 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide

    11






Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für HP Aruba 300 Series wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Holen Sie sich Ihr Benutzerhandbuch per E-Mail

Geben Sie Ihre E-Mail-Adresse ein, um das Handbuch zu erhalten von HP Aruba 300 Series in der Sprache / Sprachen: Englisch als Anhang in Ihrer E-Mail.

Das Handbuch ist 1 mb groß.

 

Sie erhalten das Handbuch in Ihrer E-Mail innerhalb von Minuten. Wenn Sie keine E-Mail erhalten haben, haben Sie wahrscheinlich die falsche E-Mail-Adresse eingegeben oder Ihre Mailbox ist zu voll. Darüber hinaus kann es sein, dass Ihr ISP eine maximale Größe für E-Mails empfangen kann.

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info