477562
24
Zoom out
Zoom in
Vorherige Seite
1/100
Nächste Seite
24
2
TO ASSEMBLE BAGGER
Unfold bag and stand right side up.
Uninstall carriage bolts (5/16-18 x 1.5) and nuts (1) from the
front of the top frame.
Snap bottom of front bagger frame (3) into snap feature at
front of bagger bottom.
Remove cross braces (4) from inside of bagger assembly.
Slide cross brace (4) onto pin (5) at the rear of the upper
bagger frame and secure with retainer spring clip (6).
Slide cross brace (4) onto pin (7) at the front of the bagger
frame and secure with retainer spring clip (8).
Repeat on opposite side.
TO INSTALL BAGGER SUPPORT ASSEMBLY
Using a T30 Torx socket, loosen set screw (1). Remove
clevis pin (2) and spring clip (3).
NOTE: Set screw (1) should be loosened first and then upon
reinstallation of bagger support assembly, tightened down last.
Slide bagger support mount (4) off of bagger support tube
(5).
Repeat these steps for both bagger support assemblies.
Remove clevis pin (9) and retainer spring (10) from bagger
handle (11).
Slide bagger handle (11) down through bagger cover and
frame holes.
Reinstall clevis pin (9) through hole at bottom of bagger
handle (11) and slide retainer spring (10) into hole at the end
of the clevis pin (9) until it locks into place.
Feed front bagger frame (2) up through fabric loops at each
side of bagger.
Reinstall carriage bolts and nuts (1) to connect front frame to
top frame, passing through bagger.
Remove the mounting bolts (6) from the back of the unit.
Using those same mounting bolts (6), install the bagger
support mounts (4) onto the back of the unit.
Tighten bolts (6) to 40,7 Nm.
Reinstall bagger support tubes (5) into both bagger support
mounts (4). For both bagger support tubes, reinstall clevis
pins (2) and spring clips (3).
Retighten set screw (1).
CAUTION: Do not exceed 100 In-Lbs/11,2 Nm.
3
5
5
2
1
4
4
2
2
5
1
4
3
1
3
4
5
7
8
6
2
1
6
6
4
11
11
9
10
24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Husqvarna CTH194 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info