477562
79
Zoom out
Zoom in
Vorherige Seite
1/100
Nächste Seite
79
To Level Mower
Make sure tires are properly inflated to the PSI shown on
tires. If tires are over or under inflated, it may affect the ap-
pearance of your lawn and lead you to think the mower is
not adjusted properly.
VISUAL SIDE-TO-SIDE ADJUSTMENT
1. With all tires properly inflated and if your lawn appears un-
evenly cut, determine which side of mower is cutting lower.
2. With a 3/4" or adjustable wrench, turn lift link adjustment
nut (A) to the left to lower the mower, or, to the right to
raise the mower (Fig. 1).
NOTE: Each full turn of adjustment nut will change mower
height about 3/16".
3. Test your adjustment by mowing some uncut grass and
visually checking the appearance. Readjust, if necessary,
until you are satisfied with the results.
PRECISION SIDE-TO-SIDE ADJUSTMENT
1. With all tires properly inflated, park tractor on level ground
or driveway.
CAUTION: Blade is sharp. Protect your hands with gloves
and/or wrap blade with heavy cloth.
2. Raise mower to its highest position.
3. At both sides of mower, position blade at side and measure
the distance (A) from bottom edge of blade to the ground.
The distance should be the same on both sides (Fig. 2).
4. If adjustment is necessary, see step 2 in Visual Adjust-
ment instructions above.
5. Recheck measurements, adjust if necessary until both
sides are equal.
FRONT-TO-BACK ADJUSTMENT
IMPORTANT: Deck must be level side-to-side.
To obtain the best cutting re sults, the mower blades should
be adjusted so the front tip is 1/8" to 3/8" lower than the rear
tip when the mower is in its highest position.
CAUTION: Blade is sharp. Protect your hands with gloves
and/or wrap blade with heavy cloth.
Raise mower to highest position.
Position blade so the tip is pointing straight forward.
Measure distance (B) to the ground at front and rear tip
of the blade (Fig. 3).
If front tip of blade is not 1/8" to 3/8" lower than the rear
tip, go to the front of tractor.
With an 11/16" or adjustable wrench, loosen jam nut A
several turns to clear adjustment nut B.
With a 3/4" or adjustable wrench, turn front link adjustment
nut (B) clockwise (ltighten) to raise the front of mower, or,
counterclockwise (loosen) to lower the front mower (Fig. 4).
NOTE: Each full turn of the adjustment nut will change mower
height about 1/8".
Recheck measurements, adjust if necessary until front
tip of blade is 1/8" to 3/8" lower than the rear tip.
Hold adjustment nut in position with wrench and tighten
jam nut securely against adjustment nut.
6
02966
AA
Fig. 2
02548
BB
Fig. 3
Fig. 4
B
B
A
A
A
Fig. 4
79

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Husqvarna CTH194 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info