Bedienungsanleitung Hyundai 56020 (Seite 4 von 9) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

675850

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

HYUNDAI

6 7

ENGLISH

NOISE AND VIBRATION

Typically the A-weighted sound pressure level of

the machine is 91.4 dB(A). Uncertainty K = 3.0

dB(A).

The noise level when working can exceed 102.4

dB(A).

Wear hearing protection!

Vibration emission value a

h,D

= 15.05 m/s

Uncertainty K = 1.5 m/s

GUARANTEE

Refer to the enclosed guarantee conditions for the

terms and conditions of guarantee.

ENVIRONMENT

Disposal

Your product, accessories and packaging should

be sorted for environmental-friendly recycling.

Do not dispose of power tools into domestic

waste. According to the European Guideline

2002/96/EC for Waste Electrical and Electronic

Equipment and its implementation into national

right, power tools that are no longer usable must

be collected separately and disposed of in an

environmentally friendly way.

Subject to change; specifications can be changed

without further notice.

Changing the direction of rotation (fig. A)

• Press the forward/reverse switch (4) to the left

to drill or to fasten screws.

• Press the forward/reverse switch (4) to the

right to loosen screws.

• Set the forward/reverse switch (4) to the

middle position to lock the machine.

Always wait until the motor has come

to a complete standstill before

changing the direction of rotation.

Adjusting the speed (fig. A)

This machine has been tted with an adjusting

wheel (2) for the maximum speed.

• Turn the adjusting wheel (2) as indicated on

switch (1) to set the maximum speed.

Switching on and off (fig. A)

• To switch the machine on, press the on/off

switch (1). The further you press the switch,

the higher the speed of the machine.

• To switch off the machine, release the on/off

switch (1).

• To switch the machine to continuous mode,

keep the on/off switch (1) pressed and at the

same time press the lock-on button (3).

• Subsequently release the on/off switch.

• To switch off continuous mode, press the on/

off switch (1) again.

CLEANING AND MAINTENANCE

The machine does not require any special main-

tenance.

• Regularly clean the ventilation slots.

TECHNICAL DATA 56020

Mains voltage V 230-240

Mains frequency Hz 50

Power input W 710

No load speed min

-1

0-2,900

Impact (no load min

-1

0-48,000

Drilling capacity in

steel mm 13

wood mm 25

concrete mm 13

Chuck mm 13

Weight kg 1.77

Depth stop

Chuck key

Instruction manual

Safety warnings

Guarantee and service

Inserting and removing a drill or screw bit (fig.

• Open the chuck (7).

• Insert the drill or the screw bit in the chuck.

• Tighten the chuck by hand.

• Tighten the chuck firmly by inserting the chuck

key in one of the holes in the side of the chuck

and turning it clockwise.

• In order to remove a drill or screw bit, proceed

in reverse order.

Before inserting or removing a drill or

screw bit always remove the plug from

the outlet.

Mounting the side handle (fig. A)

• Loosen the knob on the side handle.

• Slide the side handle (6) over the chuck on the

machine.

• Turn the side handle in the required position

and tighten the knob firmly.

Mounting the depth stop (fig. A)

The depth stop is used to limit the maximum

drilling depth.

• Loosen the knob on the side grip.

• Insert the depth stop (8) in its intended hole in

the side grip.

• Set the depth stop to the required drilling

depth.

• Tighten knob firmly.

Selecting the operating mode (fig. A)

Select the required operating mode before use

(drilling or hammer drilling).

• For drilling in wood, metal, plastics and soft

stone and for driving screws slide the switch

(5) to the left.

• For drilling in concrete or hard stone slide the

switch (5) to the right.

Always wait until the motor has come

to a complete standstill before

changing the operating mode.

ELECTRONIC HAMMER

DRILL

56020

WARNING

Read all safety warnings and all

instructions. Failure to follow the

warnings and instructions may result in

electric shock, re and/or serious

injury. Save all warnings and

instructions for future reference.

SAFETY WARNINGS

When using the machine, always observe the

enclosed safety warnings as well as the additional

safety warnings.

The following symbols are used throughout this

manual:

Denotes risk of personal injury or

damage to the machine.

ADDITIONAL SAFETY WARNINGS FOR

ELECTRONIC HAMMER DRILLS

Personal safety

• Do not work materials containing asbestos.

Asbestos is considered carcinogenic.

ELECTRICAL SAFETY

Always check that the power supply

corresponds to the voltage on the

rating plate.

DESCRIPTION (fig. A)

Your electronic hammer drill has been designed

for drilling in wood, metal, plastic, stone and

concrete and it also has been designed for screw

driving applications.

1. On/off-switch

2. Speed adjusting wheel

3. Lock button

4. Forward/reverse switch

5. Switch hammer drill function

6. Side handle

7. Chuck

8. Depth stop

The package contains the following parts:

Electronic hammer drill

Side handle

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hyundai 56020 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info