HYUNDAI
8 9
ENGLISH
Flexible hose
The exible hose is provided with adapters for connection to the
sander and the dust bag. The dissipation function ensures that static
electricity, which sometimes occurs during sanding, is eliminated.
ASSEMBLY
any other dust collection container.
Mounting the hose to the sander (g. B)
• Loosen the nut (8) on the connection on the machine (9) in an
anti-clockwise direction.
• Push the adapter (5) at the end of the hose into the socket.
• Tighten the nut clockwise again.
Assembly and changing of the abrasive discs (g. C)
from the outlet.
The sander can be used with sanding discs with and without
extraction holes.
• Loosen the nut (10) of the disc holder (11) anticlockwise.
• Remove the nut, metal ring and sanding disc.
• Place a sanding disc. Block the disc holder and repeat the
previous procedure in reverse order. Make sure that the disk and
the attachment are properly installed.
Use the support ring to set the sanding depth.
USE
produced when using the sander. This dust can interfere
dangerously with your and others health. Kindly always
wear a protection mask against dust when using this
product. Keep people and animals away from the work
area when the device is running.
Switching on and off
The sander must be turned off (on OFF switch) before connecting it.
• Connect the power cable to the power supply
• To start the tool, turn the switch (2) to the ON position.
• To stop the sander, turn the switch to OFF position.
Speed adjustment
This sander is equipped with adjustable speed. The speed can be
controlled with the speed control (1). A higher speed should be used
for leveling and removal. A lower speed can be used for precise
renement.
Sanding
Place the correct sanding disc for the surface to be sanded (ceiling,
corner of the ceiling, different parts of a wall).
When sanding a wall or ceiling, use a ladder to reach the area to be
scoured.
Sanding tips
• Place the sander against the working surface with suitable
strength.
• Apply additional pressure for a stronger removal and reduce the
pressure for a smoother and more accurate finish.
• Apply enough pressure to keep the sanding plate flat against the
wall surface. However, excessive pressure can cause rubbing
marks or even irregularities on the worked surface.
• Keep the sander in constant motion while holding the sanding
plate in contact with the surface to be sanded.
• Use a steady, stable sweeping motion, balancing strength well.
Irregular movements and even stopping on the working surface
loose or cracked wires. If power tool or accessory is dropped,
inspect for damage or install an undamaged accessory. After
inspecting and installing an accessory, position yourself and
bystanders away from the plane of the rotating accessory and
run the power tool at maximum no-load speed for one minute.
Damaged accessories will normally break apart during this test time.
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing protectors, gloves
and workshop apron capable of stopping small abrasive or
workpiece fragments.
The eye protection must be capable of stopping ying debris
generated by various operations. The dust mask or respirator
must be capable of ltrating particles generated by your operation.
Prolonged exposure to high intensity noise may cause hearing loss.
Keep bystanders a safe distance away from work area. Anyone
entering the work area must wear personal protective equipment.
Fragments of workpiece or of a broken accessory may y away and
cause injury beyond immediate area of operation.
Hold power tool by insulated gripping surfaces only, when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord.
Cutting accessory contacting a “live” wire may make exposed metal
parts of the power tool “live” and shock the operator.
Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged and your hand or
arm may be pulled into the spinning accessory.
Never lay the power tool down until the accessory has come to
a complete stop.
The spinning accessory may grab the surface and pull the power
tool out of your control.
Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could snag your
clothing, pulling the accessory into your body.
Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical hazards.
Do not operate the power tool near ammable materials.
Sparks could ignite these materials.
Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in electrocution or
shock.
Kickback and related warnings
Kickback is a sudden reaction to a pinched or attaching a rotating
accessory. Pinching or hanging causes rapid stalling of the rotating
accessory which in turn forced the tool Power out of control in the
opposite direction of rotation of the accessory to the point of seizing.
For example, if an abrasive wheel is snagged or pinched by the
workpiece, the edge of the wheel that is entering into the pinch point
can dig into the surface of the material, causing jumps or expulsion
of the grinding wheel. The wheel can jump towards the operator
or by moving away, as the direction of movement of the grinding
wheel at the point of pinch. Abrasive wheels may also break under
these conditions. Kickback is the result of misuse of the tool and / or
procedures or conditions incorrect operation and can be avoided by
taking proper precautions specied below.
Maintain rmly the power tool and position your body and arm
for you allow to resist kickback forces. Always use auxiliary
handle, where applicable, for maximum control of kickback or
torque reaction during startup.
WALL AND CEILING SANDER
56476
WARNING
Failure to
follow the warnings and instructions may result in electric
shock, re and/or serious injury. Save all warnings and
instructions for future reference.
SAFETY WARNINGS
When using the machine, always observe the enclosed safety
warnings as well as the additional safety warnings.
Wear a dust mask.
Wear eye protection.
Wear hearing protection.
Wear gloves.
The following symbols are used throughout this manual:
ADDITIONAL SAFETY WARNINGS FOR WALL AND
CEILING SANDERS
This power tool is intended to function as a sander. Read all
safety warnings, instructions, illustrations and specications
provided with this power tool.
Failure to follow all instructions listed below may result in electric
shock, re and/or serious injury.
Operations such as grinding, wire brushing, polishing or
cutting-off are not recommended to be performed with this
power tool.
Operations for which the power tool was not designed may create a
hazard and cause personal injury.
Do not use accessories which are not specically designed and
recommended by the tool manufacturer.
Just because the accessory can be attached to your power tool, it
does not assure safe operation.
The rated speed of the accessory must be at least equal to the
maximum speed marked on the power tool.
Accessories running faster than their rated speed can break and y
apart.
The outside diameter and the thickness of your accessory must
be within the capacity rating of your power tool.
Incorrectly sized accessories cannot be adequately guarded or
controlled.
The arbour size of wheels, anges, backing pads or any other
accessory must properly t the spindle of the power tool.
Accessories with arbour holes that do not match the mounting
hardware of the power tool will run out of balance, vibrate
excessively and may cause loss of control.
Do not use a damaged accessory. Before each use inspect
the accessory such as abrasive wheels for chips and cracks,
backing pad for cracks, tear or excess wear, wire brush for
The operator can control the reaction torques or forces rebound, if
precautions are taken.
Never place your hand near the rotating accessory.
The accessory can perform a bounce on your hand.
Do not place you in the area where power tool will move if
kickback.
The rebound pushes the tool in the opposite direction to movement
of the wheel in point hooking.
Take special care when working corners, sharp edges etc.
Avoid twists and snaps of the accessory.
Corners, edges or sharp twists tend to hang the rotating accessory
and cause loss of control or kickback.
Additional safety instructions for sanding operations
Do not use sandpaper too oversized for sanding discs. Follow
manufacturers’ recommendations when selecting sanding paper.
More abrasive paper extending beyond the sanding pad presents
a laceration hazard and may cause a crash, tearing of the disc or
kickback.
WARNING
user and for people in the vicinity.
• It is not recommended to sand lead paint. Lead paint must be
removed by a specialist only.
• Do not work on materials that release hazardous substances (eg
asbestos).
• Take precautionary measures if hazardous, flammable or
explosive dust can occur. Wear a protective dust mask.
• If drywall or gypsum is sanded, static electricity may be
generated on the tool. To ensure your safety, the wall sander is
grounded.
ELECTRICAL SAFETY
voltage on the rating plate.
DESCRIPTION (g. A)
This tool is designed for sanding of plastered walls and ceilings,
removal of wallpaper and carpet residues, paint layers, glue
residues, loose plaster and for sanding oors.
1. Speed controller
2. On/off switch
3. Dust bag
4. Hose
5. Adaptor
6. Strap
7. Extra handle
The package contains the following parts:
Wall and ceiling sander
6 abrasive discs (80-240)
Hex key
Screwdriver
Adaptor
Dust bag
Flexible hose
Carrying belt
6 hoops
Support ring
Set of carbon brushes
Instruction manual
Safety warnings
Guarantee and service
