Bedienungsanleitung I-onik WS-105 (Seite 5 von 6) (Deutsch, Englisch)

521908

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

8 9

3.2 Installing the Garage Door

Sensor

• Mount the transmitter on a

xed at surface on or close to

the garage door frame using

either double-sided adhesive

strips or the screws and wall

plugs provided.

• Mount the transmitter contact

onto the garage door frame opposite the

magnetic contact which should be attached to

the garage door.

• The >/< markings on the contacts need to be directly

opposite each other and no more than 10 mm apart when

the door is closed (Fig. 2).

3.3 Installing using Double-sided Adhesive Pads

• Ensure the mounting surfaces are clean.

• Peel back one layer of the protective lm and attach it to the

transmitter.

• Peel back the remaining layer of protective lm and press the

transmitter rmly in place against the mounting surface until

attached.

• Repeat the process to attach the transmitter contact and the

magnetic contact.

4. House Security Code Settings

Unless the factory settings of the i.onik

Alarmsystem Smart

Panel have been altered, the House Security Code will NOT

need to be changed.

However, if the settings on the Smart Panel have been altered,

or need to be altered to solve the problem of the Smart Panel

and sensors activating intermittently (or not working at all) or

interference with other systems, then the House Security Code

on all system modules (sensors and sirens)will also need to be

changed.

House Security Code settings can be altered as follows:

• There are 4 jumpers or dip-switches on each device.

• Remove the jumper compartment cover, then pull out or plug

the jumper into the contacts to change the House Security

Code.

• If a jumper is plugged it is ON if it is removed it is OFF.

Default code is with all the jumpers plugged.

• To ensure the system works correctly, make sure the jumpers

on the Smart Panel and all other system modules (sensors

and sirens) match exactly.

Jumpers for

house

security code

- Smart Panel

- Each sensor

Default house code:

1: ON, 2: ON, 3: ON, 4: ON

*Jumper: ON = Plugged,

OFF = Pull Out

Dip-Switches

for house

security code

- Key Fob Remote

Default house code:

1: ON, 2: ON, 3: ON, 4: ON

Fig. 2

5. Zone Code Settings

• Unscrew and remove the jumper compartment cover on the

rear of the sensor.

• In the area marked “Zone Code” there are eight pairs of

metal contacts with a number next to each.

• The number corresponding to the pair of contacts which is

plugged with a jumper is the current zone.

• To re-assign to a different zone simply unplug the jumper

from its current zone and plug it across the contacts corres-

ponding to the new zone number selected.

Jumpers for

zone code

Default zone code: Zone 1

6. Maintenance

The product may be cleaned with a soft damp cloth and then

wiped dry. Do not use abrasive, solvent based or aerosol clea-

ners as this may damage and/or discolour the product. Do not

allow water to enter or attempt to clean inside the unit.

7. Batteries

Do not allow the batteries to corrode or leak as this may cause

permanent damage to the product. Take care to insert the

batteries with the correct polarity as shown inside the battery

compartments. Do not mix new and old batteries or different

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

I-onik WS-105 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info