670299
18
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
4
MAINTENANCE
15
PROBLEM POSSIBLE CAUSE SOLUTION REF.
Power does not come
on when the [POWER]
switch is pushed.
Cable connection is faulty.
The circuit breaker is turned OFF.
Check the connection and connection cable
pins.
Check for the cause, then turn the circuit
breaker ON.
pgs.
79
p. 3
Sensitivity is low. The antenna is not connected properly.
The antenna for another band is
selected.
The antenna is not properly tuned.
Reconnect the antenna connector.
Select an antenna suitable for the operating
frequency.
Push [TUNER] for 2 sec. to manually tune the
antenna.
p. 6
p. 13
p. 14
Output power is too
low.
Reverse connection on the antenna input
and output.
[ALC adj] is not adjusted properly.
The linear amplifier circuit is turned OFF.
The antenna for another band is
selected.
The antenna is not properly tuned.
The protector circuit activates and a band
indicator blinks.
Connect properly.
Set [ALC adj] properly.
Push [AMP/PROTECT] to turn the linear
amplifier ON. (The indicator lights green.)
Select an antenna suitable for the operating
frequency.
Push [TUNER] for 2 sec. to manually tune the
antenna.
Stop the exciters transmission, then push
[AMP/PROTECT] to deactivate the protection
circuit.
pgs.
79
p. 11
p. 13
p. 13
p. 13
p. 14
Protection circuit
activates during short
periods of operation.
Antenna SWR is more than 3:1.
The antenna tuner is turned OFF.
The linear amplifier is located in an area
with bad air circulation.
[ALC adj] is not adjusted properly.
Check the antenna SWR. Adjust the antenna, if
necessary.
Push [TUNER] to turn the antenna tuner ON.
Select a location with good air circulation.
Adjust [ALC adj] to the correct position.
p. 6
p. 14
p. 11
Operating band does
not change
automatically.
Cable connection is faulty.
The CI-V setting is not properly
programmed.
Check the connection and connection cable
pins.
Set the CI-V address.
pgs.
79
p. 12
Troubleshooting
The following chart is designed to help you correct
problems which are not equipment malfunctions.
If you are unable to locate the cause of a problem or
solve it through the use of this chart, contact your near-
est Icom Dealer or Service Center.
18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Icom iPW1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info