468476
5
Zoom out
Zoom in
Vorherige Seite
1/7
Nächste Seite
15
Timer
The timer can be used to set a max.
cooking time of 99 minutes (1 hour and
39 minutes) for one cooking zone only.
Select the cooking zone to be used with
the timer (an illuminated dot appears to the bottom right
hand side of the heat setting indicator on the display), then
set the desired cooking time using the buttons “+” and “-”
of the timer function (see figure above). A few seconds
after the button is pressed, the timer begins the countdown
(the luminous dot of the selected cooking zone starts
flashing). Once the set time has elapsed, an acoustic signal
sounds and the cooking zone switches off automatically.
To deactivate the timer, press the button “-” until the
display shows “0:0” or press the buttons “+” and “-” of
the timer at the same time.
Caution!
The timer function can only be used
with one cooking zone at a time.
Minute minder
The minute minder can only be used when the hob is not
in use and allows a maximum setting of 99 min.
Press the button “+” above the timer indicators:
the display shows the minutes for setting.
Select the time desired using the buttons + and -.
After a few seconds the minute minder starts to count
down. Once the set time has elapsed an acoustic signal
sounds.
Caution!
The minute minder function can only
be used when the hob is switched off; if it is then
switched on, the minute minder countdown is
automatically cancelled.
Control panel warnings
Residual heat indicator.
The hob is fitted with a residual heat indicator for
each cooking zone. These indicators alert the user
when cooking zones are still hot.
If the display shows , the cooking zone is still hot.
If the residual heat indicator of a given cooking zone is lit,
that zone can be used, for example, to keep a dish warm
or to melt butter.
When the cooking zone cools down, the display switches
off.
Incorrect or missing pot indicator.
The hob features an automatic pot detection
system for all cooking zones. If no pot is detected,
the display with the cooking zone power level
indicator flashes. Make sure the pot is correctly
positioned and that it has the characteristics given in the
section “Before use”.
61901363GB.fm Page 15 Tuesday, January 1, 2002 3:20 AM
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

ikea-nutid-hin4t

Suche zurücksetzen

  • nutid hci 4t blinkt nur platte keine wärme schaltet sich nicht ein beide funktionieren nicht
    Eingereicht am 12-11-2017 15:48

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Ikea NUTID HIN4T wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info