IT 58
Cosa far
Se la lavastoviglie non funziona corr
riportato. Per errori o pr
contatto sono riportati nel libretto di gar
per almeno 10 anni dalla data di produzione dell'
Problemi... Possibili cause... Soluzioni...
What t o do if ... What t o do if ...
In case your dishwasher doesn’t work properly , check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty
booklet. The manufacturer ensures the availability of spare parts for at least 10 years after production date of this appliance.
PROBLEMS POSSIBLE CAUSES SOLUTIONS
Salt indicator is lit
Salt reservoir is empty . (After refill
the salt indicator may remain lit
for several wash cycles).
Refill reservoir with sal (for more information - see page 8).
Adjust water hardness - see table, page 8 .
Rinse aid indicator is lit
Rinse aid dispenser is empty .
(After refill the rinse aid indicator
may remain lit for several wash
cycles).
Refill dispenser with rinse aid (for more information - see page 8) .
The dishwasher won’t start
or does not respond to
commands.
The appliance has not been
plugged in properly . Insert the plug into the socket.
Power outage. The dishwasher starts automatically when the power returns.
The dishwasher door is not closed. V igorously push the door until you hear the “click” .
It does not respond to commands.
Display shows: 9 or 12 and
On/Of f LED is blinking rapidly .
Switch of f the appliance by pressing the ON/OFF button, switch it
back on after approximately one minute and reset the program.
If problem persists, unplug the appliance for 1 minute, then plug it
back in.
The dishwasher won’t drain.
Display shows: 3 and
On/Of f LED is blinking
rapidly
The wash cycle has not finished yet W ait until the wash cycle finishes
The drain hose is bent. Check that the drain hose is not bent (see INST ALLA TION).
The sink drain pipe is blocked. Clean the sink drain pipe.
The filter is clogged up with food
residues. Clean the filter (see CLEANING THE FIL TER ASSEMBL Y).
The dishwasher makes
excessive noise.
The dishes are rattling against
each. Arrange the crockery correctly (see LOADING THE RACKS).
An excessive amount of foam has
been produced.
The detergent has not been measured out correctly or it is not
suitable for use in dishwashers (see FILLING THE DETERGENT
DISPENSER) . Reset the current cycle by switching OFF the
dishwasher , then switch it on again, select a new program, press
ST AR T/Pause and close the door within 4 seconds. Please do not
add any detergent.
The dishes are not clean.
The crockery has not been
arranged properly . Arrange the crockery correctly (see LOADING THE RACKS).
The spray arms cannot rotate freely ,
being hindered by the dishes. Arrange the crockery correctly (see LOADING THE RACKS).
The wash cycle is too gentle
and/or detergent efficiency is lo . Select an appropriate wash cycle (see PROGRAMS T ABLE).
An excessive amount of foam has
been produced.
The detergent has not been measured out correctly or it is not suitable
for use in dishwashers ( see FILLING THE DETERGENT DISPENSER) .
The cap on the rinse aid compart -
ment has not been shut correctly . Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged Clean the filter assembly (see CARE AND MAINTENANCE).
There is no salt. Fill the salt reservoir (see FILLING THE SAL T RESER VOIR).
The dishwasher does not fill
the water .
Display shows: H
6
and On/Of f LED is blin-
king
rapidly
No water in the water supply or
the tap is closed. Make sure there is water in the water supply or the tap running.
The inlet hose is bent. Make sure the inlet hose is not bent (see INST ALLA TION) repro-
gram the dishwasher and reboot.
The sieve in the water inlet hose
is clogged; it is necessary to
clean it.
After having carried out the verification and cleaning, turn o f and
turn on the dishwasher and restart a new program.
Spia del sale accesa
Il serbatoio del sale è vuoto.
(È possibile che, dopo
riempito il serbatoio, la spia del
sale resti accesa per diversi cicli
di lavaggio).
Riempire il serbatoio con sale (per ulteriori informazioni,
vedere a pagina 8).
Regolare la dur
What t o do if ... What t o do if ...
In case your dishwasher doesn’t work properly , check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty
booklet. The manufacturer ensures the availability of spare parts for at least 10 years after production date of this appliance.
PROBLEMS POSSIBLE CAUSES SOLUTIONS
Salt indicator is lit
Salt reservoir is empty . (After refill
the salt indicator may remain lit
for several wash cycles).
Refill reservoir with sal (for more information - see page 8).
Adjust water hardness - see table, page 8 .
Rinse aid indicator is lit
Rinse aid dispenser is empty .
(After refill the rinse aid indicator
may remain lit for several wash
cycles).
Refill dispenser with rinse aid (for more information - see page 8) .
The dishwasher won’t start
or does not respond to
commands.
The appliance has not been
plugged in properly . Insert the plug into the socket.
Power outage. The dishwasher starts automatically when the power returns.
The dishwasher door is not closed. V igorously push the door until you hear the “click” .
It does not respond to commands.
Display shows: 9 or 12 and
On/Of f LED is blinking rapidly .
Switch of f the appliance by pressing the ON/OFF button, switch it
back on after approximately one minute and reset the program.
If problem persists, unplug the appliance for 1 minute, then plug it
back in.
The dishwasher won’t drain.
Display shows: 3 and
On/Of f LED is blinking
rapidly
The wash cycle has not finished yet W ait until the wash cycle finishes
The drain hose is bent. Check that the drain hose is not bent (see INST ALLA TION).
The sink drain pipe is blocked. Clean the sink drain pipe.
The filter is clogged up with food
residues. Clean the filter (see CLEANING THE FIL TER ASSEMBL Y).
The dishwasher makes
excessive noise.
The dishes are rattling against
each. Arrange the crockery correctly (see LOADING THE RACKS).
An excessive amount of foam has
been produced.
The detergent has not been measured out correctly or it is not
suitable for use in dishwashers (see FILLING THE DETERGENT
DISPENSER) . Reset the current cycle by switching OFF the
dishwasher , then switch it on again, select a new program, press
ST AR T/Pause and close the door within 4 seconds. Please do not
add any detergent.
The dishes are not clean.
The crockery has not been
arranged properly . Arrange the crockery correctly (see LOADING THE RACKS).
The spray arms cannot rotate freely ,
being hindered by the dishes. Arrange the crockery correctly (see LOADING THE RACKS).
The wash cycle is too gentle
and/or detergent efficiency is lo . Select an appropriate wash cycle (see PROGRAMS T ABLE).
An excessive amount of foam has
been produced.
The detergent has not been measured out correctly or it is not suitable
for use in dishwashers ( see FILLING THE DETERGENT DISPENSER) .
The cap on the rinse aid compart -
ment has not been shut correctly . Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged Clean the filter assembly (see CARE AND MAINTENANCE).
There is no salt. Fill the salt reservoir (see FILLING THE SAL T RESER VOIR).
The dishwasher does not fill
the water .
Display shows: H
6
and On/Of f LED is blin-
king
rapidly
No water in the water supply or
the tap is closed. Make sure there is water in the water supply or the tap running.
The inlet hose is bent. Make sure the inlet hose is not bent (see INST ALLA TION) repro-
gram the dishwasher and reboot.
The sieve in the water inlet hose
is clogged; it is necessary to
clean it.
After having carried out the verification and cleaning, turn o f and
turn on the dishwasher and restart a new program.
Spia del brillantante
accesa
Il distributore del brillantante
è vuoto.
aver riempito la vaschetta, la spia
del brillantante resti accesa per
diversi cicli di lavaggio).
Riempire la vaschetta con brillantante (per ulteriori
informazioni, vedere pagina 8).
La lavastoviglie non si avvia o
i comandi non rispondono.
L
collegato correttamente
all'
Inserire la spina nella pr
Mancanza di corrente. Per ragioni di sicur
automaticamente al ripristino della corrente elettrica. Aprir
lo sportello della lavastoviglie, pr
richiudere lo sportello entr
Mancata chiusura della porta
lavastoviglie.
La spina Natural Dry non è
inserita.
Spingere con decisione la porta no ad avvertir
caratteristico “ clic” .
Mancato funzionamento dei
vari comandi. Sul display viene
visualizzato: 9 o 12 e il LED On/
O lampeggia rapidamente.
Spegnere l'
riaccenderlo dopo circa un minuto e riavviar
Se il problema persiste, staccar
elettrica per un minuto, quindi ricollegarlo.
Lo scarico della lavastoviglie
non avviene.
Sul display viene visualizzato:
3 e il LED On/O lampeggia
rapidamente
Ciclo di lavaggio non ancora
concluso Attendere la conclusione del ciclo di lavaggio
T Vericar
sezione INST
T
ostruito. Pulire il tubo di scarico del lavandino.
Ostruzione ltro a causa di
residui di cibo. Pulire il ltr
La rumorosità della
lavastoviglie è eccessiva.
Urto dei piatti tra lor
lavaggio. Sistemare le sto
CARICAMENTO DEI CESTELLI).
Produzione eccessiva di
schiuma. Il dosaggio del detersivo non è stato stabilito in modo
corretto oppur
lavastoviglie (veder
DETERSIVO). Per riavviare il ciclo in corso, spegner
riaccendere la lavasto
premer
Non aggiungere altr
I piatti non risultano puliti.
Errata disposizione delle
stoviglie. Sistemar
CARICAMENTO DEI CESTELLI).
Impedimento nella rotazione
dei bracci aspersori a causa
dell'interferenza dei piatti.
Sistemare le sto
CARICAMENTO DEI CESTELLI).
Ciclo di lavaggio eccessivamente
delicato e/o detersivo di scarsa
ecacia.
Selezionare il pr
PROGRAMMI).
Produzione eccessiva di
schiuma. Il dosaggio del detersivo non è stato stabilito in modo corretto
oppure il detersivo non è del tipo adatto alle lavasto
RIEMPIMENTO DEL DISTRIBUT
T
correttamente chiuso. Accertarsi che il tappo sul distributore brillantante sia chiuso.
Filtro spor Pulir
Mancanza di sale. Riempire il serbatoio del sale (veder
SERBA
