Bedienungsanleitung Indesit DI 620 (Seite 12 von 16) (Englisch)

34625

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Installation

Positioning the Appliance

Position the appliance in the desired location. The back

should rest against the wall behind it, and the sides, along

the adjacent cabinets or wall. The dishwasher is equipped

with water supply and drain hoses that can be positioned to

the right or the left to facilitate proper installation.

Levelling the Appliance

Once the appliance is positioned, adjust the feet (screwing

them in or out) to adjust the height of the dishwasher, making

it level. In any case, the appliance should not be inclined

more than 2°.

If the appliance is level, it will help ensure proper perfor-

mance.

Cold Water Connection

Connect the cold water supply hose to a threaded 3/4 (gas)

connector.

If the water pipes are new or have not been used for an

extended period of time, let the water run to make sure that

the water is clear and free of impurities. If this precaution is

not taken, there is a risk that the water inlet can get

blocked and damage the appliance.

Hot Water Connection

The water supply to the appliance can also be connected to

the house's hot water line (centralised system, heating

system), as long as it does not exceed a temperature of

60°C.

In this case, the wash cycle time will be shortened by about

15 minutes and the wash efficiency slightly reduced.

The connection must be made to the hot water line following

the same procedures as those for the connection to the cold

water line.

Drain Hose Connection

Fit the drain pipe into a drain line with a minimum diameter

of 4 cm or place it over the sink. Avoid restricting or bending

it. Use the special plastic elbow provided (see figure) to

position it in the best possible way. The part of the pipe

marked with the letter A should be between 40 and 100 cm

above the ground.

The pipe should not be immersed in water.

Electrical Connection

After making sure that the voltage and frequency values for

the current in the home correspond to those on the rating

plate (located on the stainless steel inner door of the

appliance) and that the electrical system is sized for the

maximum voltage on the rating plate, insert the plug into

an electrical socket which is earthed properly (the earthing

of the appliance is a safety requirement mandated by law).

If the electrical socket to which the appliance must be

connected is not appropriate for the plug, replace the plug,

rather than using adpators or the like as they could cause

overheating and burns.

Caution: the dishwasher plug must be accessible even

when the appliance is installed as a built-in unit so

that maintenance can be done safely.

Should the electricity supply cable be damaged, we

recommend that you only contact authorised Technical Service

Centres for the replacement.

Condensation-proof tape.

On some models, a transparent condensation-proof adhesive

tape has been provided.

It should be stuck onto the lower side of your wooden worktop

to protect it from the formation of condensation.

When not provided, this tape can be requested as a spare

part from authorised retailers.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit DI 620 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info