Bedienungsanleitung Indesit FE10KC (Seite 7 von 8) (Englisch)

55991

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Instalation

The appliance must be installed only by a qualified

person in compliance with the instructions provided.

The manufacturer declines all responsibility for improper

installation which may harm persons and animals and

damage property.

Important: The power supply to the appliance must be

cut off before any adjustments or maintenance work is

done on it.

Installation of Built-in Ovens

In order to ensure that the built-in appliance functions prop-

erly, the cabinet containing it must be appropriate. The

figure below gives the dimensions of the cut-out for instal-

lation under the counter or in a wall cabinet unit.

In order to ensure adequate ventilation, the back panel of

the cabinet unit must be removed. Installing the oven so

that it rests on two strips of wood is preferable. If the oven

rests on a continuous, flat surface, there must be an ap-

erture of at least 45 x 560 mm.

The panels of the adjacent cabinets must be made of heat-

resistant material. In particular, cabinets with a veneer ex-

terior must be assembled with glues which can withstand

temperatures of up to 100 °C.

In compliance with current safety standards, contact with

the electrical parts of the oven must not be possible once

it has been installed.

All parts which ensure the safe operation of the appliance

must be removable only with the aid of a tool.

To fasten the oven to the cabinet, open the door of the

oven and attach it by inserting the 4 wooden screws into

the 4 holes located on the perimeter of the frame.

The panels of the adjacent cabinets must be made of

heat resistant material. In particular, cabinets with a veneer

exterior must be assembled with glues able to withstand

temperatures of up to 100°C.

Once the appliance has been installed, the electrical parts

must be totally protected from all contact, according to

current safety regulations.

All protecting parts should be firmly fixed and should

require the use of a tool for removal.

When installing below a built-in hob, ensure that there are

air inlets and outlets for ventilating the interior of the cabinet

adequately. Assembly examples are given in figs.

Electrical connection

Ovens with a three-pole power supply cable are designed

to operate with alternated current at the supply frequency

and voltage indicated on the data plate (at the bottom of

the oven dashboard). The earthing conductor of the cable

is the yellow-green conductor.

Two types of connection are provided:

Connection n° 1

Connecting the power supply cable to the mains.

Fit a normalized plug to the cable, which corresponds to

the load indicated on the data plate; if the cooker is

connected directly to the mains, an omnipolar circuit-

breaker with a minimum opening of 3 mm between the

contacts, suitable for the load indicated and complying

with current directives, must be installed between the

appliance and the mains (the earthing wire must not be

595 mm.

24 mm.

545 mm.

5 mm.

567 mm.

23 mm.

593 mm.

45 mm.

558 mm.

N.B.: Installation in compliance with the consumption declaration

595 mm.

24 mm.

545 mm.

5 mm.

567 mm.

23 mm.

575-585 mm.

558 mm.

595 mm.

45 mm.

min.

45 mm.

min.

560 mm.

45 mm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit FE10KC Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info