Bedienungsanleitung Indesit IDE1000 (Seite 11 von 13) (Englisch)

46872

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

Cleaning and Special Maintenance

Troubleshooting

It may occur that the dishwasher does not function or does not

function properly. Before calling for assistance, let us see what can

be done first: have you forgot to press one of the buttons or to

perform an essential operation?

The Dishwasher Does Not Start

Have you checked whether:

- the plug is pushed into the socket correctly;

- the power is on in the house;

- the door is closed properly;

- the ON-OFF switch is on "ON";

- the water supply is turned on.

The Dishwasher Does Not Load Water

Have you checked whether:

- the water is turned on and the hose is connected properly;

- the water supply to the house is on and has sufficient

pressure;

- the water supply hose is crimped or bent;

- the filter for the water supply hose is clogged.

The Dishes Are Not Clean

Have you put the right amount of detergent into the dispenser?

Is the wash cycle suitable for the dishes you have placed inside the

appliance?

Are the filter and microfilter clean?

Can the sprayer arms turn freely?

The Dishwasher Does Not Drain

Have you checked whether:

- the drain hose is crimped or bent.

Lime Deposits or a White Film Form on the Dishes

Have you checked whether:

- the lid to the salt container is closed properly;

- the rinse aid dosage is correct.

If the display indicates the word "dON" when you turn your

dishwasher on, this means the demo mode is in operation.

Read the instructions on pages 7.

Error messages.

Your dishwasher is equipped with a safety system which is able to

detect any operating anomalies.

These anomalies or faults are signalled by several codes consisting of

letters and numbers that flash up on the display. Make a note of the

error code that appears, turn the appliance off, turn off the water

tap and call for technical assistance.

Tap off alarm

If you have forgotten to turn on the water tap, the appliance will

remind you with a series of prolonged beeps and the wording H2O

will flash up on the display. Turn the tap on and the wash cycle will

start up after a few minutes.

If you are not there when the H2O signal appears, the appliance will

switch to alarm mode and the code "A06" will flash on the display.

Turn the appliance off at button "A", turn on the water tap and wait

approximately 20 seconds before turning the appliance back on, the

wash cycle will start up again.

Clogged filter alarm

If the appliance is blocked and the code "A05" is flashing, this means

the filter is clogged by large particles of food residue. Turn the

appliance off at the ON-OFF button, clean the filter thoroughly and

reposition it in its seat, then turn the appliance back on. The wash

cycle will start up as normal after a few seconds.

Water load solenoid valve malfunction alarm

If the code "A02" flashes,

first of all turn off the water tap to avoid

any flooding and then cut off the electricity supply and call for

assistance.

If, despite all these checks, the dishwasher still does not function

and/or the problem persists, contact the nearest authorised service

centre and provide them with the following information:

- the nature of the problem;

- the model type number (Mod. ...) and the serial number (S/N ....),

which are indicated on the plate located on the side of the inner part

of the door.

Never call on unauthorised technicians and refuse to allow

parts to be installed that are not original spare parts.

The filter assembly

If you want consistent good results from your dishwasher, you need

to clean the filter assembly.

The food particles are removed from the wash water, allowing it to

be recirculated during the

cycle, filtered perfectly. For

this reason, it is a good idea

to remove the larger food

particles trapped inside the

semi-circular filter A and

cup “C”after each wash; to

remove the filter assembly,

pull the cup handle

upwards. All you need to do

is rinse them under running

water.

The entire filter assembly

should be cleaned

thoroughly once a month:

semi-circular filter A + cup

C + cylindrical filter B+

microfilter D.

To remove filter “B”, turn it anti-clockwise. Use a small non-metallic

brush for cleaning.

Reassemble the filter parts (as shown in the figure) and reinsert the

whole assembly into the dishwasher. Position it into its housing and

press downwards.

The dishwasher is not to be used without filters. Improper replacement

of the filters may reduce the efficiency of the wash and even damage

your dishwasher.

Cleaning the Sprayer Arms

It may happen that food particle become encrusted on the

sprayer arms and block the holes (see "Close up view

(interior)", letters F-I). Check the sprayer arms periodically

and clean them when needed.

Cleaning the Water Inlet Filter

Periodically clean the water inlet filter (see figure 2 under

"Installation") located on the outlet of the water supply

tap. After turning off the water tap, unscrew the end of

the water supply hose, remove the filter and clean it carefully

under running water. Then, return the filter to its place and

tighten the water supply hose back into position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit IDE1000 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Indesit IDE1000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info